Kenmore 141.16315800 manual Tools Required forAssembly, 8am-8pm CST, Monday throu.qh Friday, Bes

Failure to comply with these instructions may

result in a hazardous situation which, if not avoided, may result in injury.

Spiders and small insects can spin webs and

nest	in	the	grill	ring transit		and
warehousing				Ls flow
obstruction				round		the
Burner Tc				FIRE"
can	CAM'.					an
unsafe
To				.'K
FIRE					bes
as				grill.
Also	do			summer
and	fall	or		in	your
area,	and		if	used	for	an
extended		period

1.Remove the screw from the rear of each Burner using a Phillips Head Screwdriver.

2.Carefully lift each Burner up and away from the Gas Valve Orifice.

3.Check and clean Burner Tubes for insects and insect nests. A clogged tube can lead to a fire beneath the grill.

4.Refer to the figure below and perform one of

these 3 cleaning methods:

[] METHOD 1: Bend a stiff wire or wire coat hanger into a small hook as shown and run the hook through the Burner Tube and inside the Burner several times to remove debris.

,)

TOCLEAN BURNER

TUBE, INSERT HOOK

\

Burner Tube Foot

[] METHOD 2: Use a bottle brush with a flexible handle and run the brush through the Burner Tube and inside the Burner several times to remove any debris.

[] METHOD 3: Use an air hose to force air through each Burner Tube. The forced air

should pass debris or obstructions through the Burner and out the Ports.

For safe operation ensure the Gas Valve Assem- bly Orifice is inside the Burner Tube before using your grill. See figure. If the Orifice is not inside the Burner Tube, lighting the Burner may cause

explosion and/or fire resulting in serious bodily injury and/or property damage.

Huuuuuuuuuuuuuuuu[

Gas Valve Assembly OrificeBumerTube

1.Do not store spare LP cylinder within 10 feet (3m) of this appliance.

2.Do not store or use gasoline or

other flammable liquids and vapors within 25 feet (8m) of this appliance.

3.When cooking with oil/grease, do not allow the oil/grease to get hotter than 350°F (117°C).

4.Do not leave oil/grease unattended.

1.Do not store or use gasoline or other flammable liquids in the vicin- ity of this or any other appliance.

2.An LP cylinder not connected for use shall not be stored in the

vicinity of this or any other appliance.

PRE-ASSEMBLY

Read and perform the following pre-assembly instructions:

[] Tools Required forAssembly :

	•	protective			work	gloves
	•	protective			eyewear
[]	•	#2	&	#3	Phillips	HeadScrewdriver			person to
	You will		neee assistance				Trom another
	handle	the		grill head and other large,				heavy parts.

[] Open Lid of shipping carton and remove parts box and packing materials. Lay cardboard sheet on floor and use as a work surface to protect floor and grill parts from scratches.

[] You may slice the carton front corners with a utility knife to lay open the carton front panel. This allows you to raise the grill head Lid and remove the

components packed inside, making it easier to lift. Use the sliced off carton front as a work surface to

protect floor and grill parts from scratches.

[] Use the Hardware and Part Diagrams to ensure all items are included and free of damage.

[] Do not assemble or operate the grill if it appears damaged. If there are damaged or missing parts when you unpack the shipping cartons or you have

questions during the assembly process, call the:

Grill Information Center 1-888-317-7642

8am-8pm CST, Monday throu.qh Friday

Grill Installation Codes

The installation must conform with local codes or, in the absence of local codes, with either the National

Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas

and Propance Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2.