321 Studios OL-2706-01 manual Installation Overview

Page 16

Chapter 2 Provisioning

Step by Step Installation and Initial Configuration

Installation Overview

The installation procedure for the Cisco CNS Configuration Registrar is straightforward. The software is installed and configured through a console connection to the serial port. The console connection parameters are the same as for other Cisco IOS devices, that is:

9600 baud

Parity: 8/None

Stop bits: 1.

 

 

 

Step 1

After the Cisco CNS IE2100 appliance is optionally racked, plugged in, and turned on, insert the

 

 

 

 

CDROM installation disk and press the Reset button.

 

 

 

 

You can not monitor the installation procedure as the console logic does not begin until the Operating

 

 

 

 

System is started. After the automatic installation procedure completes, the CD ejects automatically and

 

 

 

 

the system restarts, at which point the login prompt appears in the Console window.

 

 

 

Step 2

Log in as user setup.

 

 

 

 

The Setup program starts.

 

 

 

Step 3

Enter responses to the prompts that appear.

 

 

 

 

After you enter a response, you cannot edit it again. To change an entered response, you must exit the

 

 

 

 

Setup program and enter your responses again. You can exit the Setup program in two ways:

 

 

 

 

Press Ctrl-c. The login prompt appears. Use the login setup to run the Setup program.

 

 

 

 

Enter n at the final prompt. The Setup program exits, then restarts.

 

 

 

 

Refer to the sample setup session below for an example of the prompts and their responses:

 

 

 

Step 4

Press ESC to log in:

 

 

 

 

USER ID:

 

 

 

 

LILO

 

 

 

 

boot:

 

 

 

 

boot:

 

 

 

 

Loading linux

 

 

 

 

Linux version 2.4.2-2 (root@porky.devel.redhat.com) (gcc version 2.96

 

 

 

 

20000731 (Red Hat Linux 7.1 2.96-79)) #1 Sun Apr 8 20:41:30 EDT 2001

 

 

 

 

BIOS-provided physical RAM map:

 

 

 

 

BIOS-e820: 000000000009dc00 @ 0000000000000000 (usable)

 

 

 

 

BIOS-e820: 0000000000002400 @ 000000000009dc00 (reserved)

 

 

 

 

BIOS-e820: 0000000000020000 @ 00000000000e0000 (reserved)

 

 

 

 

BIOS-e820: 000000003feec340 @ 0000000000100000 (usable)

 

 

 

 

BIOS-e820: 0000000000010000 @ 000000003fff0000 (reserved)

 

 

 

 

BIOS-e820: 0000000000003cc0 @ 000000003ffec340 (ACPI data)

 

 

 

 

BIOS-e820: 0000000001400000 @ 00000000fec00000 (reserved)

 

 

 

 

127MB HIGHMEM available.

 

 

 

 

On node 0 totalpages: 262124

 

 

 

 

zone(0): 4096 pages.

 

 

 

 

zone DMA has max 32 cached pages.

 

 

 

 

zone(1): 225280 pages.

 

 

 

 

zone Normal has max 1024 cached pages.

 

 

 

Cisco Internet OSS for VoIP: Infrastructure Manager Implementation Guide

 

 

 

 

2-16

 

 

OL-2706-01

 

 

 

 

 

Image 16
Contents Provisioning DescriptionTarget Market Scope of the SolutionDocument Purpose Open Packet Telephony Overview Examples of Open Packet Telephony NetworksMgcp Packet Voice Network Virtual Switch Virtual Entities in the NetworkNMS Architecture MGC CNSIoss Provisioning Component Architecture Functional Description Interconnection/InteroperabilityComponent List Cisco Packet Telephony CenterCisco Voice Routing Center Cisco Media Gateway Control Node ManagerLess than Entry level UltraSparcIII 9GB with at leastCmnm Features Active Host Standby HostCmnm Configuration Cmnm TroubleshootingRecommended Hardware Configuration for Cmnm Voice Services Provisioning Tool Recommended Hardware Configuration for VsptRecommended Hardware Configuration for CiscoView CiscoViewCisco CNS Intelligence Engine and Cisco CNS Bus Technology Cisco CNS Intelligence EngineHardware Requirements Installing the Cisco CNS IE2100 Configuration Engine Overview of InstallationDependencies Installation Overview PCI PCI Scsi Chapter Provisioning Localhost.localdomain login setup Cisco Intelligence Engine Enter the Secondary DNS Server IP address OL-2706-01 Http//hostname or IP address of IE2100/config/login.html Planning and Installation Checklist Gathering Installation SoftwareDetermining the Hardware Requirements for Your Environment Installing the Solaris 8 Patch ClusterEnsuring the Network Devices have the Correct Software Ptc-tme#mkdir patches Cnote-tme# ./installclusterPtc-tme#cd patches Dependencies with the following commands Host# showrev -p Host# showrev -p grepObtaining a Cisco EMF License Cmnm-pri# hostidOrder of Installation Checking System PrerequisitesCmnm-pri#nslookup cmnm-pri Cmnm-pri#cd /opt/images cmnm-pri#pwdUntar the contents of the CSCOvspt-2.3.1.tarfile List the contents of the directory Cmnm-pri# ls -lCmnm-pri# ./setup -nodisplay Cmnm-pri# mkdir tmp cmnm-pri# cd tmp cmnm-pri# lsInstallation Summary Following items were installed Untar the contents of the CSCOvspt-2.3.1-patch-01.tarfile Cmnm-pri#tar -xvof CSCOvspt-2.3.1-patch-01.tarOutput suppressed Checking for Package Install Installing Cemf 3.2 and Available PatchesCheck to ensure the entire package was installed Cmnm-pri#cd cdrom/cdrom0 Cmnm-pri# ./cemfinstallIs this setup correct? y y,n,? Cemf Manager Installation OL-2706-01 Page Cemf Patch Installation ?-----------output suppressed------------------------?List the contents of the Patch directory Cmnm-pri# ls List the contents of the current directory Cmnm-pri# lsNow do the same with Patch Invoke the Cemf installation scriptCmnm-pri#tar -xvof CEMF3.2P3.2.tar Start the Cemf application Starting CemfCmnm-pri#cd /opt/cemf Cmnm-pri#bin/cemf start Before installing CMNM, ensure Cemf is running Installing the Cisco MGC Node ManagerCmnm-pri#cd /opt/cemf Cmnm-pri#bin/cemf query Cmnm-pri#ps -ef grep vold Cmnm-pri#cd /cdrom/cscocmnm Cmnm-pri# ./installCSCOcmnmCmnm-pri# /etc/init.d/volmgt start Output suppressed Verifying class none Installation of CSCOcmnm was successful Opt/cemf/help/CSCOcmnm/cdapp/launched ?-----------------output suppressed-----------------------? ## Reading Package Files Done Output suppressed ## Executing actions Verifying Correct Installation Before Continuing Cmnm-pri#pkginfo -l CSCOcmnmObtain Cmnm version information Cmnm-pri#bin/cmnmversion -verboseVerifying the Installation of CiscoView Installing Cmnm PatchesCmnm-pri#pkginfo -l CSCOcmcv Cmnm-pri# ./patchCSCOcmnmVerifying Patch Installation Success Starting CmnmCemf Logo Window Installing Cisco PTC 2.1.1 Integrated with Cisco VRC # cd /scratch/cvUpgradeUpgrading CiscoView Cisco PTC Client RequirementsProduct Prerequisite Cisco PTC Dependencies on Platform VersionsIntegrated Product Component Installing Cisco PTC Optional Product ComponentsCisco PTC Server Installation Pre Installation Checks#pkginfo -l Cnsc #pkginfo l Tibrv Installing the Cnsc Core Package Copying Cisco PTC Files From the Product CDCnsc Core CNS Integration BUS CNS Security Java Tomcat VRC Ptc-tme%pkginfo -l Cnsc Ptc-tme# ./cnscInstall Ptc-tme#pkginfo -l TibrvInstalling the Java and Tomcat Packages Ptc-tme# cd /opt/vnm/commonInstalling the Cisco Voice Routing Center Application Ptc-tme#pwd /opt/PTC-2.1.1 Ptc-tme# ./cnscInstallPtc-tme#cd /opt/vnm/common Opt/vnm/common/jakarta-tomcat-3.3.1 directory existsIors Installing the Voice Corba Gateway on the Cmnm Host Ptc-tme#more /.cshrcWhen prompted, enter 1 as the number of EMSs Ptc-tme#which shareThis is the password to login to the Cmnm host machine Cmnm-tme#ps -ef grep ObjectAccess Cmnm-tme#ps -ef grep McgNotifyServerSynchronizing Cmnm with the SC2200 Cisco PTC Patch Information02011801.tar 02011802.tar 02011804.tar System Startup Ptc-tme% dcdstartVerify the Cisco CNS Security process is running Ptc-tme%ps -ef grep dcx500Verify the Cisco CNS Integration Bus is running Ptc-tme%ps -ef grep rvrdPage Post Installation Configuration Configuring the Cisco PTC ClientGo to the /opt/cisco/vnm directory Ptc-tme%cd /opt/cisco/vnmImplementation and Testing OL-2706-01