Weber 3000 Series owner manual Install side burner locks, Add cooking box

Page 12

Step 7

Install side burner locks

Note: The locks are taped to the inside of the side burner lid.

You will need: frame assembly, two side burner lock and a 7/16 inch wrench.

Turn frame assembly right side up.

Loosen the right rear 1/4 x 20 bolt. Install the side burner lock. The “U” shape cut out of the lock slips down over the bolt. Tighten with a wrench. Figure 6 (a).

Loosen the right front 1/4 x 20 bolt. The side burner lock fits between the front panel and the frame. The “U” shape cut out slips up over the bolt. Tighten with a wrench. Figure 6 (b).

Slide the cooking box to the left within the frame. Put the washer on the bolt. Insert the bolt through the cooking box and frame with the head of the bolt outside the box. Figure 8. Add keps nut. Tighten by holding the bolt with pliers while you tighten the nut with the 7/16 inch wrench.

Figure 8

(a)

(b)Your Weber Gas Barbecue burner assembly has been

factory assembled, pressure and flame tested. As a safety precaution we recommend you check the burner alignment:

a) Do the valves fit into the ends of the burners? Figure 9 (a).

b)Are the ends of the burners under the washers at the left rear and left front of the cooking box? The screws

are only guides. Do not tighten. Figure 9 (b).

c) Are the wing nuts under the burner assembly hand tight? Do not tighten with pliers. Figure 9 (c).

Figure 6

If you answered YES to a, b and c, the burners are

correctly aligned. If you answered NO, the burners are

 

 

misaligned. Contact Weber-Stephen Customer Service.

 

Do not use your barbecue.

 

Guide screw

Step 8

Add cooking box

(b)

You will need: frame assembly, cooking box assembly, 1/4- 20 x 2 inch bolt, nylon washer, 1/4-20 acorn nut, pliers and a 7/16 inch wrench.

Set the cooking box into the frame so the burner tubes are under the frame brace. Figure 7.

Burner tubes

Frame brace

Figure 9

(a)

(c)

Wing nuts

Figure 7

12

Image 12
Contents Genesis 3000 Series MDANGER MWARNINGS LP GAS Units onlyWarranty Patents and Trademarks Contents For Installation in Canada Gas supply testingGeneral Instructions StorageAssembly Check package contentsStep BER E W REB Check contents of hardware packs Assemble wheels Assemble frameContinue frame assembly Complete frame assemblyInsert casters Install side burner locks Add cooking boxInstall gas supply General Specifications for PipingGas line piping Test connectionsInstall igniter Check that all burner valves are off Connect flexible hose to manifoldInstall side burner Install manifold bracketMWARNING Make sure gas supply is OFF Check for gas leaks Death and damage to propertyMWARNING Do not ignite burners while leak checking Install Flavorizer Bars and Cooking Grates Install the bottom tray Install the lidSecure side burner MCAUTION Make sure both locks have snapped into placeInstall swing table Complete accessory installation Lighting To ExtinguishTurn gas supply OFF at the source, then push down Manual Lighting Lighting the side burner Lighting only the side burner. FigurePeriodic Cleaning CookingStorage and/or Nonuse Drippings and greaseAnnual Maintenance Inspection and Cleaning of the Weber Spider Stopper GuardsGeneral Maintenance Main Burner Cleaning ProcedureWeber Spider Stopper Guards Main Burner Flame PatternView from behind cooking box Wing nuts Crossover Ignition System Operations Burner does not light, or flame is low in High position Burner flame pattern is erratic. Flame is lowSide Burner Troubleshooting Side Burner Maintenance14-15 17-18,15 21-22 26 27 Parts List Use only Weber factory authorized parts.Page Page Final Word Thanks