Weber 3000 Series Lighting, To Extinguish, Turn gas supply OFF at the source, then push down

Page 22

OPERATING INSTRUCTIONS

Lighting

Summary lighting instructions are on the control panel.

mDANGER

Failure to open lid while igniting the barbecue, or not waiting 5 minutes to allow the gas to clear if the barbecue does not light, may result in an explosive flame- up which can cause serious bodily injury or death.

Crossover Ignition System

Note - The Crossover Ignition System ignites the Front burner with a spark from the igniter electrode inside the Gas Catcher Ignition Chamber. You generate the energy for the spark by pushing the Crossover Ignition Button until it clicks.

mWARNING: Check hose before each use of barbecue for nicks, cracking, abrasions or cuts. If the hose is found to be damaged in any way, do not use the barbecue. Replace using only Weber authorized replacement hose. Order from Weber-Stephen Products Co., Customer Service Center or authorized dealer.

1)Open the lid. Figure 1.

2)Make sure all burner control knobs are turned OFF. (Push each burner control knob down and turn clockwise.)

3)Turn gas supply valve on.

4)Push Front burner control knob down and turn to START/HI.

mWARNING: Do not lean over open barbecue. Keep your face and body at least one foot away from the matchlight hole when lighting the barbecue.

5)Push the Crossover Ignition Button several times, so it clicks each time.

6)Check that the burner is lit by looking through the matchlight hole on the front of the cooking box.

mWARNING: If the burner does not light, turn the

Front burner control knob to OFF and wait 5 minutes to let the gas clear before you try again or try to light with a match.

7)After the FRONT burner is lit you can turn on the other burners.

1

Crossover Ignition System

Note - Always light the FRONT burner first. The other burners ignite from the FRONT burner.

6 4

 

 

To Extinguish

2

 

Turn gas supply OFF at the source, then push down

 

and turn each burner control knob clockwise to OFF.

 

7

 

 

3

5

Figure 1

22

Image 22
Contents Genesis 3000 Series MDANGER MWARNINGS LP GAS Units onlyWarranty Patents and Trademarks Contents General Instructions For Installation in CanadaGas supply testing StorageCheck package contents AssemblyStep BER E W REB Check contents of hardware packs Assemble wheels Assemble frameComplete frame assembly Continue frame assemblyInsert casters Install side burner locks Add cooking boxGas line piping Install gas supplyGeneral Specifications for Piping Test connectionsInstall igniter Check that all burner valves are off Connect flexible hose to manifoldInstall manifold bracket Install side burnerMWARNING Make sure gas supply is OFF Death and damage to property Check for gas leaksMWARNING Do not ignite burners while leak checking Install Flavorizer Bars and Cooking Grates Install the bottom tray Install the lidSecure side burner MCAUTION Make sure both locks have snapped into placeInstall swing table Complete accessory installation To Extinguish LightingTurn gas supply OFF at the source, then push down Manual Lighting Lighting the side burner Lighting only the side burner. FigureStorage and/or Nonuse Periodic CleaningCooking Drippings and greaseAnnual Maintenance Inspection and Cleaning of the Weber Spider Stopper GuardsWeber Spider Stopper Guards General MaintenanceMain Burner Cleaning Procedure Main Burner Flame PatternView from behind cooking box Wing nuts Crossover Ignition System Operations Burner does not light, or flame is low in High position Burner flame pattern is erratic. Flame is lowSide Burner Troubleshooting Side Burner Maintenance14-15 17-18,15 21-22 26 27 Parts List Use only Weber factory authorized parts.Page Page Final Word Thanks