Emerson NGA 2000 TO2 Single Component Display, Display Status…, Main… Channel BasicCal

Page 33

Model NGA 2000 TO2

Instruction Manual

760008-A September 2001

b.Single Component Display

The Measure menu that displays after startup is the Single Component display of the analyzer. If other analyzer modules

are connected to the Platform, it is possi- ble to display them using the following steps to change the channel of the single component display:

TO2
37.50					ppm O2

0.00		Range: 3		50.00
Electrolyte level:		OK
Temp current:		263 uA	0.0	600
Range:		3

Sensor Current:		0.0500 uA	0.0000	100.0000

Display Status… Main… Channel BasicCal

MLT/CH1/R2

2.50% CO2

Press F4 (Channel) to change to the Single Component Display of any other installed Analyzer Modules.

Example:

Changing from TO2 (channel 1) to CO2 (channel 2).

Note: Display may look different depending on installed analyzers.

Continue pressing F4 to display the desired channel depending on the installed analyzer configuration, ultimately returning to the first channel.

0.00

Temperature:

Maintenance-Requests:

Any-alarms:

Operation:

Display Status…

Range: 2

5.00

37.0C 0.0 No

No

Ready

Main… Channel BasicCal

Single component display of the starting channel.

TO2
37.50					ppm O2

0.00		Range: 3		50.00
Electrolyte level:		OK
Temp current:		263 uA	0	600
Range:		3

Sensor Current:		0.0500 uA	0.0000	100.0000

Display Status…

Main…

Channel

BasicCal

Figure 3-11. Single Component Display

Rosemount Analytical Inc. A Division of Emerson Process Management

Operation 3-9

Image 33

Contents Model NGA 2000 TO2 Essential Instructions Model NGA 2000 TO2 Table of ContentsMaterial Safety Data Sheet System & Network I/O Module Controls SetupAnalyzer Module Interconnection with Instrument Platform List of IllustrationsModel NGA 2000 TO2 Definitions Preface Intended USE StatementSafety Summary Model NGA 2000 TO2 Compliances DocumentationGlossary of Terms System SoftkeysFeatures Section Description and SpecificationsOverview Typical ApplicationsTrace Oxygen Detector Coulometric Principle Trace Oxygen Analyzer Module Top View General SPECIFICATIONS1Sample PhysicalGas Connections Model NGA 2000 TO2 Unpacking Section InstallationElectrolyte Electrolyte AdditionGAS Connections GasesGAS Overpressure Sample FlowLeak Test Sensor DamageElectrical Connections Electrical Shock Hazard Analyzer Module Interconnection with Instrument Platform Outline and Mounting Dimensions Back Panel Connections Displays & Operating Keys OperationAnalyzer basic controls calibration & setup… Menu Lines & Softkey FunctionalityMeasure Status… Channel Lock… MFG Data Signal on mini-bargraph Entering & Changing VariablesMeasure Back… Measure Mode Display Ppm O2Display Status… Main… Channel BasicCal Module Manufacturing Data Displays Startup & Initialization LCDReset AbortQuick Start Initiate quick startMeasure Status… Back… Power supply voltages… Measure Back… Basic CONTROLS, Setup and StatusAnalyzer Channel Status Display Status… Main… ChannelSingle Component Display Display Status…Main… Channel BasicCal Multi Component Display Select Status… Tags Off LCDResetRange number Basic Controls and SetupOperation Status Range numberBrightness and Contrast Display ControlsDisplay controls… Brightness 70 %Analyzer and I/O, expert controls & setup… Expert Controls and SetupAnalyzer module controls… Measure Channel Back…Gas Scale Factor Calibration ProcedureAir background gas concentration Gas scale factor…Span gas 90.0 ppm Measure Status… Back… Span CalibrationAlarms… AlarmsConcentration alarm setup… Measure Back… ClrAlm Alarm generation isReRanges… RangesBegin / end of ranges… Range Begin PpmMeasurement Display Configuration Measurement display configuration…Linearization Gas measurement units Concentration MeasurementConcentration measurement… Gas concentration unitsSensor model Temperature compensation at span gasClamp low PVA to Ppm to mg/Nm3 conversion factorFlow Measurement Flow measurement…Flow lower limit 400 ml/min Temperature Measurement Temperature measurement… Measure Status… Back…Temperature measurement units System & network I/O module controls… System & Network I/O Module CON Trols Setup37.50 ppm System SIO module…System SIO Analog output setup…Choose signal Analog Output SetupSelect analog output number Choose the analyzer moduleSignal value for 0% output Hold output during calibrationHold output during calibration Operation mode Outputs value on analyzer failureOutput number Type of installed serial inter- face Analog Output Updates Per SecondOutput #1 Yes Baud rate 19200Invert signal Relay Outputs SetupCommunication protocol Choose source moduleSystem DIO Choose signal…Function control Input numberSystem Configuration and DIAG- Nostics Diagnostic Menus Load/Save Module Configura- tionAnalyzer Module Diagnostics Security Codes Date and TimeSystem Reset System reset Measure Back…Entering a level locked by security code Model NGA 2000 TO2 Section Maintenance and Service Overview Electrical Shock HazardSensor Caustic Liquid Refilling Sensor Sensor AssemblyElectrolyte Replacement Sensor ReplacementSensor Lleak Check Linearization Analyzer and I/O expert controls & setup…Do not tilt Sensor excessively as elec- trolyte may leak Time & DateLinearization… Linearization temperature values…0000 ppm Linearization raw values sensor current…Electronic Components Flow Sensor ReplacementFuses Printed Circuit BoardsTroubleshooting Section TroubleshootingFailure to purge down to ppm levels Erratic and very insensitive readingsModel NGA 2000 TO2 Section Replacement Parts MatrixTO2 NGA 2000 TO2 Trace Oxygen Analyzer Module Replacement Parts Section Return of Material Customer ServiceReturn of Material TrainingModel NGA 2000 TO2 Section Index Model NGA 2000 TO2 Product ELECTROLYTE1 Precautions to be taken in handling Emergency & first aid proceduresOther precautions Threshold limit value Routes of entryRosemount Warranty Asia Pacific EUROPE, Middle EAST, Africa Latin America