Invacare Pronto M61 manual Depth, Adjusting the Footboard Assembly Angle

Page 47

SECTION 8—FOOTBOARD ASSEMBLY

Bottom View of	Set Screw, Washer
Footboard		and Jam Nut

Footboard

Assembly

FIGURE 8.2 Adjusting the Footboard Assembly - Angle

Depth

NOTE: For this procedure, refer to FIGURE 8.3.

1.Remove the quick release pin that secures the footboard assembly to the wheelchair frame.

WARNING

Make sure the detent balls of the quick-release pin are fully released and beyond the outer edge of the tube before operating the wheelchair. Otherwise, injury and/or damage may result.

Keep detent balls clean.

2.Adjust footboard to one of three mounting positions.

3.Install the quick release pin. Make sure the detent balls of the quick‐release pin are fully released and beyond the outer edge of the tube (Detail “A”).

Top Shroud

Three Depth

Adjustment Holes

Footboard

Assembly

Mounting

DETAIL “A” - BOTTOM VIEW OF

FOOTBOARD

Quick Release Pin

Hole

Quick	Detent
Release Pin	Ball

Outer Edge

of Tube

Detent Balls

FIGURE 8.3 Adjusting the Footboard Assembly - Depth

Part No 1125085

47

Pronto® M51™and M61™with SureStep®

Image 47

Contents Pronto M51and M61with SureStep Document Reference DocumentsReference Documents Table of Contents Register Your Product Table of ContentsMeaning Special NotesSpecial Notes Special Notes Label Location Label LocationTypical Product Parameters Typical Product ParametersShipping AsbaOperation Information Controller Settings/Repair or ServiceAccessories General GuidelinesImmediately Charging Batteries BatteriesM61 Wheelchairs Only Rain Test Weight TrainingWeight Limitation Grounding InstructionsEMI Information EMI InformationEMI Information Stability and Balance SAFETY/HANDLING of WheelchairsSAFETY/HANDLING of Wheelchairs Coping With Everyday Obstacles Coping With Everyday ObstaclesPinch Points Pinch PointsLifting/Stairways Lifting/Stairways Transferring To and From Other SeatsTransferring To and From Other Seats Reaching, Leaning and Bending ForwardReaching and Bending Backward Reaching and Bending BackwardAll Wheelchairs Safety INSPECTION/ TroubleshootingSafety Inspection Checklists Safety INSPECTION/TROUBLESHOOTINGInspect/Adjust Weekly Additional Requirements for M61 Wheelchairs Troubleshooting GuideSymptom Probable Cause Solutions Display Description Definition About Joystick DiagnosticsPossible Solution Service Indicator Light DiagnosticsDON’T Checking Battery Charge LevelAdditional Troubleshooting Information for M61 Wheelchairs Operating the Wheelchair Turning the Power On/OffUsing the Joystick to Drive the Wheelchair Wheelchair OperationMovement Action Adjusting the SpeedElevating the Seat Using the HornElevating the Seat LED SPJ+ and SPJ+ w/ACC Joystick Switches and IndicatorsSpeed Control Buttons Mode ButtonOn/Off Button SpeedometerInformation Gauge Display Service IndicatorJoystick Charger/Programming InputArms Removing/Installing the ArmsAdjusting the Arms Adjusting WidthAdjusting Height Adjusting AngleRemoving Installing/Removing Flip Back ArmrestsInstalling Positioning Flip Back Armrests for Use Positioning/Adjusting Flip Back ArmrestsPositioning Flip Back Armrests for User Transfer Fold Down Back Angle Adjusting the Back AngleSeat Semi-Recline Back AngleAdjusting the Back Angle Fold Down Back Angle Adjusting the Headrest Semi-Recline OnlyRemoving/Installing the Seat Assembly Removing/Installing the Seat AssemblyVan Seat Replacing the Seat Positioning StrapReplacing the Seat Positioning Strap Asba Seat Asba SeatFootboard Assembly Footboard AssemblyRemoving/Installing the Footboard Assembly Angle Adjusting the Footboard AssemblyDepth Adjusting the Footboard Assembly AngleFront Riggings Installing/Removing Front RiggingsFront Riggings Model PHWH93 Adjusting Footrest HeightModel PH904A and PHAL4A Replacing Heel LoopsOffice Style Seat Adjusting/Replacing Telescoping Front Rigging SupportsRaising/Lowering Elevating Front Riggings Position Front RiggingInch OUT Inches OUT Standard Seat Inner Mounting Holes Mounting Screws Spacer TOP Shroud and Wheels Removing/Installing the Top ShroudTOP Shroud and Wheels Replacing the Flat Free Tires on the Wheel RimTOP Shroud and Wheels Engaging/Disengaging Motor Release LeverEngaging/Disengaging Motor Release Lever Replacing Front/Rear Caster AssembliesAdjusting Forks Adjusting ForksBatteries BatteriesRemoving/Installing Batteries from/into Battery Tray Using the Proper BatteriesBatteries Tool QTY Connecting Battery Cables Connecting/Disconnecting Battery CablesBatteries Caps not shown on front Charging Batteries Disconnecting Battery CablesBattery Charger Operation On-Board Battery Charger ON/OFF Indicator Port Electronics Removing/Installing the JoystickElectronics Repositioning the Joystick Removing/Installing the JoystickRepositioning the Joystick Connecting Disconnecting/Connecting the JoystickDisconnecting Disconnecting/Connecting the Joystick Accessories AccessoriesInstalling/Removing the Crutch/Cane Holder Cylinder Installing/Removing the Oxygen HolderUsing the Walker Holder Installing/Removing/Using the Walker HolderInstalling/Removing the Walker Holder Global Limited Warranty Excluding Canada Global Limited Warranty Excluding CanadaUSA Canada Limited Warranty