Invacare R2-250, Pronto R2 Raising/Lowering Elevating Legrests, Adjusting Calfpads, Replacing

Page 17

FRONT RIGGINGS

PROCEDURE 3

RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS (FIGURE 6)

Raising/Lowering Elevating Legrests

1.Perform one (1) of the following:

RAISING - Pull back on the release lever

until the leg is at the desired height.

LOWERING - Support leg with one (1) hand and push release lever down- ward with other hand.

Adjusting Calfpads

1.Turn calfpad towards the outside of the wheelchair.

2.Slide the calfpad up or down until the desired posi- tion is obtained.

NOTE: If one (1) of the top two (2) calfpad adjustment positions is being used, the legrest will need to be raised to avoid interference with the front stabilizers while going over obstacles or going up and down ramps. Refer to RAISING/LOWERING ELEVATING LEGRESTS in this procedure of the manual.

3. Turn the calfpad towards the inside of the wheel- chair.

Release Lever

Calfpad

Rotated for

Height

Adjustment

Calfpad

Top Two (2) Calfpad

Adjustment Positions

FIGURE 6- RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS

ADJUSTING/REPLACING TELESCOPING FRONT RIGGING SUPPORT (FIGURE 7)

Adjusting

1.Remove the two (2) mounting screws, spacers and locknuts that secure the telescoping front rigging sup- port to the seat frame.

2.Perform one (1) of the following:

A.Slide existing telescoping front rigging support to one (1) of three (3) depth positions.

B.Remove existing telescoping front rigging support and install NEW telescoping front rigging support.

3.Secure telescoping front rigging at desired depth with existing two (2) mounting screws, spacers, and lock- nuts. Securely tighten.

NOTE: The two (2) telescoping front rigging supports can be positioned at different depths depending on the need of the user.

Replacing

NOTE: Observe the position of the current telescoping front rigging support before removal to ensure correct position of new support assembly.

1.Remove the existing telescoping front rigging sup- port from the wheelchair.

2.Install the new telescoping front rigging support into the wheelchair.

3.Adjust the telescoping front rigging support. Refer to

ADJUSTING TELESCOPING FRONT RIGGING SUPPORT in this procedure of the manual.

Seat Frame

Mounting Screws

Spacers

Locknut Telescoping

Front Tube

FIGURE 7 - ADJUSTING/REPLACING TELESCOPING

FRONT RIGGING SUPPORT

F R O N T

R

I

G G I N G S

17

Image 17
Contents ProntoR2/Pronto R2-250 Series Wheelchair TIE-DOWN Restraints and Seat Positioning Straps R N I N GTable of Contents Weight limitation varies with motor. Refer to Specification SRain and operators weight PerformanceGeneral Guidelines ProcedureGeneral Guidelines ProcedureGeneral Guidelines Stability and Balance SAFETY/HANDLING WheelchairsStairways Remove the occupant from the wheelchairMinimize GAP Distance Shift body weight into seat with transferFunctional Reach From a Wheelchair Reaching, Leaning, Bending and Bending ForwardReaching, Bending Backward Shipping Insert Removed Shipping Insert InstalledShipping Insert Battery Box Safety INSPECTION/TROUBLESHOOTING Safety Inspection ChecklistTroubleshooting Electrical Troubleshooting MechanicalChecking Battery Charge Level Safety INSPECTION/TROUBLESHOOTINGPROCEDURENumber of Floating Balls Will Vary According to Charge Using Hydrometer to Check Battery Cells Lead Acid FigureNumber of Floating Balls Adjusting Footrest Height INSTALLING/REMOVING Footrests FigureFront Riggings O N TProcedure Front Riggings INSTALLING/REMOVING Elevating Legrests FigureReplacing Heel Loops Figure O N T I N G SAdjusting Adjusting CalfpadsRaising/Lowering Elevating Legrests ReplacingDepth Figure Adjusting Removable FootboardAngle Figure Height FigureRemoving The Removable Footboard Plate Installing The Removable Footboard PlateAdjusting the ONE Piece Footboard HEIGHT, ANGLE, and Depth INSTALLING/REMOVING the ONE Piece Footboard FigureInstalling the One Piece Footboard Removing the One Piece FootboardAdjusting the CALF-PADS REMOVING/INSTALLING the CALF-PADS FigureAdjusting the Calf-Pad Height Figure Flat Head Screws Heel Mounting Holes FootboardAdjusting the Calf Pad Angle Figure Adjusting the Calf-Pad Width FigureLocknut Caplug Washer Hub CapRemove the two 2 hub caps from the pivot bracket Adjusting the Calf-Pad DepthNylon Calf-Pad Legrest TubeSmall Washers Calf-Pad Bracket Locknuts PivotO N T I N G Footrest Angle Adjustments Figure Adjusting Flip Back Armrests Figure INSTALLING/REMOVING Flip Back Armrests FigureArms M SProcedure Arms Adjusting Captains Seat ArmrestsAdjust top of the flip back armrest to the desired height Positioning Flip Back Armrests for UseReplacing Seat Positioning Strap Adjusting Captains Seat FigureCaptains SEAT/POSITIONING Strap P T a I N SRepositioning Mkiv Joystick Adjustable Seat Back Angle/Recliner Seat Models FigurePreparing Mkiv Joystick for USE Figure E CRepositioning Battery Charger Connector Figure Fuse Replacement FigureElectronics E C T R O N I C ST a Replacing Battery BOX Retaining Strap FigureR a P Retaining StrapENGAGING/DISENGAGING Motors with Motor Locks Figure ENGAGING/DISENGAGINGMOTORS with Clutches Figures 1Wheels Outside of Wheelchair Front of WheelchairWheels Adjusting Forks Figure Adjusting the Stabilizer FigureAdditional Adjustments for User Preference Detail B R O U D S REMOVING/INSTALLING Shrouds FigureShrouds Replacing Back or Headrest Upholstery Figure Recliner Operation FigureC L I N E R ReclinerRecliner Adjusting Back or Headrest Upholstery FigureHeadrest Upholstery Extension Cane UpholsteryBatteries T T E R I E SBatteries Connecting Battery CablesDirect Mount Method Dual U1 BatteriesConnect Battery Cable to Battery Terminal AS Shown Connect Battery Cables Ring Terminals to This Side PostsInstall the battery box tops Black battery clamp cover onto Black bat- tery cableInstalling Battery Clamp Covers RED Battery Clamp Cover Connecting Battery Cables to Batteryies TERMINALS/POSTSNegative Battery Terminal/Post Tie-Wrap Group 22NF Battery Detail aDescription and Use of Battery Chargers When to Charge Batteries FigureCharging Batteries Figure Mkiv RII JoystickDetail B Required ItemsDetail a Recommended Battery Types INSTALLING/REMOVING Battery Boxes FigureCleaning Battery Terminals Replacing BatteriesRear of Chair One 1 Connector Battery BoxRetaining Front Strap ClipR R a N T Y WarrantyUSA