Invacare Pronto R2, R2-250 manual Procedure, General Guidelines

Page 6

G E N E R A L

G U I D E L I N E S

PROCEDURE 1

GENERAL GUIDELINES

GENERAL WARNINGS (CONTINUED)

Carefully read battery/battery charger information prior to installing, servicing or operating your wheel- chair.

GROUNDING INSTRUCTIONS:

DO NOT, under any circumstances, cut or remove the round grounding prong from any plug used with or for Invacare products. Some devices are equipped with three-prong (grounding) plugs for protection against possible shock hazards. Where a two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to contact a qualified electrician and have the two-prong receptacle replaced with a properly grounded three-prong wall receptacle in accordance with the National Electrical Code. If you must use an extension cord, use ONLY a three-wire extension cord having the same or higher electrical rating as the device being connected. In addition, Invacare has placed RED/ORANGE WARNING TAGS on some equipment. DO NOT remove these tags.

RAINTEST

INVACARE has tested it’s power wheelchairs in accordance with ISO 7176 Part 9 “Rain Test”. This provides the end user or his/her assistant sufficient time to remove his/her power wheelchair from a rain storm and retain wheelchair operation.

DO NOT leave power wheelchair in a rain storm of any kind.

DO NOT use power wheelchair in a shower or leave it in a damp bathroom while taking a shower.

DO NOT leave power wheelchair in a damp area for any length of time.

Direct exposure to rain or dampness will cause the chair to malfunction electrically and mechanically; may cause the chair to prematurely rust.

Check to ensure that the battery covers are secured in place, joystick boot is NOT torn or cracked where water can enter and that all electrical connections are secure at all times.

DO NOT use the joystick if the boot is torn or cracked. If the joystick boot becomes torn or cracked, replace IMMEDIATELY.

WEIGHT TRAINING

Invacare DOES NOT recommend the use of its wheelchairs as a weight training apparatus. Invacare wheelchairs have NOT been designed or tested as a seat for any kind of weight training. If occupant uses said wheelchair as a weight training apparatus, INVACARE SHALL NOT BE LIABLE FOR BODILY INJURY AND THE WARRANTY IS VOID.

WEIGHTLIMITATION

The ProntoR2-250 Series models and the ProntoR2 models that have motors with clutches have a weight limitation of 250 lbs.

The ProntoR2 models that have motors with motor locks have a weight limitation of 300 lbs.

The ProntoR2 models that have motors with motor locks AND have the heavy duty crossbrace on the battery tray have a weight limitation of 400 lbs.

WARNING

CAUTION: IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION REGARDING THE POSSIBLE EFFECTS OF ELECTROMAGNETIC INTERFERENCE ON YOUR POWERED WHEELCHAIR.

Electromagnetic Interference (EMI) From Radio Wave sources

Powered wheelchairs and motorized scooters (in this text, both will be referred to as powered wheel- chairs) may be susceptible to electromagnetic interference (EMI), which is interfering electromagnetic energy (EM) emitted from sources such as radio stations, TV stations, amateur radio (HAM) transmitters, two way radios, and cellular phones. The interference (from radio wave sources) can cause the pow- ered wheelchair to release its brakes, move by itself, or move in unintended directions. It can also permanently damage the powered wheelchair's control system. The intensity of the interfering EM energy can be measured in volts per meter (V/m). Each powered wheelchair can resist EMI up to a certain intensity. This is called its "immunity level." The higher the immunity level, the greater the protec- tion. At this time, current technology is capable of achieving at least a 20 V/m immunity level, which would provide useful protection from the more common sources of radiated EMI. This powered wheel- chair model as shipped has an unknown immunity level.

6

Image 6
Contents ProntoR2/Pronto R2-250 Series R N I N G Wheelchair TIE-DOWN Restraints and Seat Positioning StrapsTable of Contents Rain and operators weight Specification SWeight limitation varies with motor. Refer to PerformanceProcedure General GuidelinesProcedure General GuidelinesGeneral Guidelines Stairways SAFETY/HANDLING WheelchairsStability and Balance Remove the occupant from the wheelchairFunctional Reach From a Wheelchair Shift body weight into seat with transferMinimize GAP Distance Reaching, Leaning, Bending and Bending ForwardReaching, Bending Backward Shipping Insert Installed Shipping Insert Battery BoxShipping Insert Removed Safety Inspection Checklist Safety INSPECTION/TROUBLESHOOTINGChecking Battery Charge Level Troubleshooting MechanicalTroubleshooting Electrical Safety INSPECTION/TROUBLESHOOTINGPROCEDUREUsing Hydrometer to Check Battery Cells Lead Acid Figure Number of Floating BallsNumber of Floating Balls Will Vary According to Charge Front Riggings INSTALLING/REMOVING Footrests FigureAdjusting Footrest Height O N TReplacing Heel Loops Figure INSTALLING/REMOVING Elevating Legrests FigureProcedure Front Riggings O N T I N G SRaising/Lowering Elevating Legrests Adjusting CalfpadsAdjusting ReplacingAngle Figure Adjusting Removable FootboardDepth Figure Height FigureInstalling The Removable Footboard Plate Removing The Removable Footboard PlateInstalling the One Piece Footboard INSTALLING/REMOVING the ONE Piece Footboard FigureAdjusting the ONE Piece Footboard HEIGHT, ANGLE, and Depth Removing the One Piece FootboardAdjusting the Calf-Pad Height Figure REMOVING/INSTALLING the CALF-PADS FigureAdjusting the CALF-PADS Flat Head Screws Heel Mounting Holes FootboardLocknut Caplug Washer Adjusting the Calf-Pad Width FigureAdjusting the Calf Pad Angle Figure Hub CapAdjusting the Calf-Pad Depth Remove the two 2 hub caps from the pivot bracketSmall Washers Calf-Pad Legrest TubeNylon Calf-Pad Bracket Locknuts PivotO N T I N G Footrest Angle Adjustments Figure Arms INSTALLING/REMOVING Flip Back Armrests FigureAdjusting Flip Back Armrests Figure M SAdjust top of the flip back armrest to the desired height Adjusting Captains Seat ArmrestsProcedure Arms Positioning Flip Back Armrests for UseCaptains SEAT/POSITIONING Strap Adjusting Captains Seat FigureReplacing Seat Positioning Strap P T a I N SPreparing Mkiv Joystick for USE Figure Adjustable Seat Back Angle/Recliner Seat Models FigureRepositioning Mkiv Joystick E CElectronics Fuse Replacement FigureRepositioning Battery Charger Connector Figure E C T R O N I C SR a P Replacing Battery BOX Retaining Strap FigureT a Retaining StrapWheels ENGAGING/DISENGAGINGMOTORS with Clutches Figures 1ENGAGING/DISENGAGING Motors with Motor Locks Figure Outside of Wheelchair Front of WheelchairAdjusting Forks Figure Adjusting the Stabilizer Figure Additional Adjustments for User Preference Detail BWheels REMOVING/INSTALLING Shrouds Figure ShroudsR O U D S C L I N E R Recliner Operation FigureReplacing Back or Headrest Upholstery Figure ReclinerHeadrest Upholstery Extension Adjusting Back or Headrest Upholstery FigureRecliner Cane UpholsteryT T E R I E S BatteriesDirect Mount Method Connecting Battery CablesBatteries Dual U1 BatteriesConnect Battery Cables Ring Terminals to This Side Posts Connect Battery Cable to Battery Terminal AS ShownBlack battery clamp cover onto Black bat- tery cable Installing Battery Clamp CoversInstall the battery box tops Negative Battery Terminal/Post Tie-Wrap Group 22NF Battery Connecting Battery Cables to Batteryies TERMINALS/POSTSRED Battery Clamp Cover Detail aCharging Batteries Figure When to Charge Batteries FigureDescription and Use of Battery Chargers Mkiv RII JoystickRequired Items Detail aDetail B Cleaning Battery Terminals INSTALLING/REMOVING Battery Boxes FigureRecommended Battery Types Replacing BatteriesRetaining Front One 1 Connector Battery BoxRear of Chair Strap ClipWarranty R R a N T YUSA