Invacare Pronto R2, R2-250 INSTALLING/REMOVING the ONE Piece Footboard Figure, Angle Figures 14

Page 20

PROCEDURE 3

FRONT RIGGINGS

F R O N T

R

I

G G I N G S

INSTALLING/REMOVING THE ONE PIECE FOOTBOARD (FIGURE 12)

Installing the One Piece Footboard

1.Pull the detent pin out from the support assembly.

2.While pulling detent pin, insert the legrest tube of the one piece footboard assembly into the support assembly.

WARNING

Before operating the wheelchair, ensure de- tent pin is engaged, and adjustment lever is securely tightened, otherwise, injury and/or damage may result.

3.Visually inspect and ensure that the detent pin is engaged.

4.Ensure pull ring is resting on the hex head portion of the detent pin assembly. Refer to DETAIL “A”.

5.Securely tighten the adjustment lever.

Removing the One Piece Footboard

1.Loosen, but DO NOT remove, the adjustment le- ver from the support assembly.

2.Pull the detent pin from the support assembly.

3.While pulling the detent pin, remove the one piece footboard assembly from the support assembly.

DETAIL “A”

Detent Pin

Seat

Assembly

Frame

 

Hex Head

Pull

portion of

Ring

Pull Ring

 

Legrest

SupportTube

Assembly

Adjustment

Lever

FIGURE 12 - INSTALLING/REMOVING THE ONE

PIECE FOOTBOARD

ADJUSTING THE ONE PIECE FOOTBOARD - HEIGHT, ANGLE, AND DEPTH

Height (FIGURE 13)

1.Remove the two (2) hub caps that cover the mount- ing bolt of the footboard assembly.

2.Remove the mounting bolt, locknut, two (2) caplug washers, two (2) large washers, and two (2) spac- ers that secure the footboard assembly to the legrest tube.

3.Raise or lower the footboard assembly to the de- sired mounting position on the legrest tube.

NOTE: Do NOT cover the warning label on the legrest tube shown in FIGURE 13.

4.Secure the footboard assembly to the legrest tube in the position determined in STEP 3 with the mounting bolt, two (2) cap caplug washers, two

(2)large washers, two (2) spacers and locknut. Securely tighten.

5.Replace the two (2) hub caps.

Spacers (Not Shown are positioned between the legrest tube and the

footboard assembly.)

Warning Label

Mounting

Bolt Hub Cap

Large

WasherCaplug

Washer

Locknut

Large

Washer

 

Footboard

Hub Cap

Caplug Washer

FIGURE 13 - ADJUSTING THE FOOTBOARD HEIGHT

Angle (FIGURES 14 AND 15)

1.Loosen, DO NOT remove, the four (4) flat head screws and barrel nuts that secure the footboard to the two (2) half clamps.

2.Rotate the two (2) half clamps on the pivot hinge until the desired angle is achieved.

3.Securely tighten the four (4) flat head screws to the footboard and half clamps.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents ProntoR2/Pronto R2-250 Series R N I N G Wheelchair TIE-DOWN Restraints and Seat Positioning StrapsTable of Contents Specification S Weight limitation varies with motor. Refer toRain and operators weight PerformanceProcedure General GuidelinesProcedure General GuidelinesGeneral Guidelines SAFETY/HANDLING Wheelchairs Stability and BalanceStairways Remove the occupant from the wheelchairShift body weight into seat with transfer Minimize GAP DistanceFunctional Reach From a Wheelchair Reaching, Leaning, Bending and Bending ForwardReaching, Bending Backward Shipping Insert Removed Shipping Insert InstalledShipping Insert Battery Box Safety Inspection Checklist Safety INSPECTION/TROUBLESHOOTINGTroubleshooting Mechanical Troubleshooting ElectricalChecking Battery Charge Level Safety INSPECTION/TROUBLESHOOTINGPROCEDURENumber of Floating Balls Will Vary According to Charge Using Hydrometer to Check Battery Cells Lead Acid FigureNumber of Floating Balls INSTALLING/REMOVING Footrests Figure Adjusting Footrest HeightFront Riggings O N TINSTALLING/REMOVING Elevating Legrests Figure Procedure Front RiggingsReplacing Heel Loops Figure O N T I N G SAdjusting Calfpads AdjustingRaising/Lowering Elevating Legrests ReplacingAdjusting Removable Footboard Depth FigureAngle Figure Height FigureInstalling The Removable Footboard Plate Removing The Removable Footboard PlateINSTALLING/REMOVING the ONE Piece Footboard Figure Adjusting the ONE Piece Footboard HEIGHT, ANGLE, and DepthInstalling the One Piece Footboard Removing the One Piece FootboardREMOVING/INSTALLING the CALF-PADS Figure Adjusting the CALF-PADSAdjusting the Calf-Pad Height Figure Flat Head Screws Heel Mounting Holes FootboardAdjusting the Calf-Pad Width Figure Adjusting the Calf Pad Angle FigureLocknut Caplug Washer Hub CapAdjusting the Calf-Pad Depth Remove the two 2 hub caps from the pivot bracketCalf-Pad Legrest Tube NylonSmall Washers Calf-Pad Bracket Locknuts PivotO N T I N G Footrest Angle Adjustments Figure INSTALLING/REMOVING Flip Back Armrests Figure Adjusting Flip Back Armrests FigureArms M SAdjusting Captains Seat Armrests Procedure ArmsAdjust top of the flip back armrest to the desired height Positioning Flip Back Armrests for UseAdjusting Captains Seat Figure Replacing Seat Positioning StrapCaptains SEAT/POSITIONING Strap P T a I N SAdjustable Seat Back Angle/Recliner Seat Models Figure Repositioning Mkiv JoystickPreparing Mkiv Joystick for USE Figure E CFuse Replacement Figure Repositioning Battery Charger Connector FigureElectronics E C T R O N I C SReplacing Battery BOX Retaining Strap Figure T aR a P Retaining StrapENGAGING/DISENGAGINGMOTORS with Clutches Figures 1 ENGAGING/DISENGAGING Motors with Motor Locks FigureWheels Outside of Wheelchair Front of WheelchairWheels Adjusting Forks Figure Adjusting the Stabilizer FigureAdditional Adjustments for User Preference Detail B R O U D S REMOVING/INSTALLING Shrouds FigureShrouds Recliner Operation Figure Replacing Back or Headrest Upholstery FigureC L I N E R ReclinerAdjusting Back or Headrest Upholstery Figure ReclinerHeadrest Upholstery Extension Cane UpholsteryT T E R I E S BatteriesConnecting Battery Cables BatteriesDirect Mount Method Dual U1 BatteriesConnect Battery Cables Ring Terminals to This Side Posts Connect Battery Cable to Battery Terminal AS ShownInstall the battery box tops Black battery clamp cover onto Black bat- tery cableInstalling Battery Clamp Covers Connecting Battery Cables to Batteryies TERMINALS/POSTS RED Battery Clamp CoverNegative Battery Terminal/Post Tie-Wrap Group 22NF Battery Detail aWhen to Charge Batteries Figure Description and Use of Battery ChargersCharging Batteries Figure Mkiv RII JoystickDetail B Required ItemsDetail a INSTALLING/REMOVING Battery Boxes Figure Recommended Battery TypesCleaning Battery Terminals Replacing BatteriesOne 1 Connector Battery Box Rear of ChairRetaining Front Strap ClipWarranty R R a N T YUSA
Top Page Image Contents