A&D GH-120/GH-200/GH-300/GH-202/GH-252 manual 5if Timeout, ErCd, AK, Error code, Interface Ct5

Page 38

 

t-Up

 

0

No limit

Selects the wait time to receive a

5if

Timeout

 

 

1

1 second

command.

 

 

erCd

 

 

0

No output

 

Serial

 

 

AK: ASCII code 06h

 

AK, Error code

 

1

Output

interface

 

 

Ct5

 

 

0

Not used

Controls CTS and RTS.

 

 

 

 

 

 

CTS, RTS control

 

1

Used

 

 

 

d5 fnc

ldin

 

 

0

Water temperature

Available only when density mode is

 

 

Density function

Liquid density input

 

1

Liquid density

selected

Unit

 

 

 

 

Refer to "5. Weighing Units".

 

Unit

 

 

 

 

 

 

 

 

 

 

 

C5 in

 

 

 

 

Displayed only when the internal mass value correction switch is set

Internal mass correction

 

 

to 1. Refer to "8. Calibration".

 

id

 

 

 

 

Refer to "11. ID Number And GLP Report".

ID number setting

 

 

 

 

 

 

: Factory settings. Digit is a unit of minimum weighing value.

Caution

The balance may not transmit the data completely at the specified refresh rate, depending on the baud rate or data added to the weighing data such as time, date and ID number.

36

Page 37 Page 39
Image 38
Page 37 Page 39
Contents GH-120 GH-200 GH-300 GH-202 GH-252 1WMPD4000891CPage Contents Underhook Density Measurement Interface And CommunicationIntroduction About This ManualCompliance With FCC Rules FeaturesCompliance Compliance With EMC DirectivesPage Unpacking the Balance Before Use PrecautionsInstalling the Balance During Use ShockPower Supply After UseDisplay Display Symbols and Key OperationKey When pressed and released When pressed and held Key operationWeighing Units Units101 00001 Examples Unit Display Gram Counting mode Pcs Percent mode Densitymode Press the PrintChanging the Units Balance displaysUnit setting example Read . Display symbols and Key operation before operation Precautions for the weighing operationBasic Operation Gram Mode Weighing01mg Dual RangeWeighing range Available minimum display 1mgCounting operation Counting Mode PCSStoring a sample unit mass Weighing input mode Counting mode using the Acai function Mark turns off after Unit mass is improved RepeatStoring the 100% reference mass Percent Mode %Selecting the percent mode Reading the percentageAdvise Response AdjustmentAutomatic Response Adjustment Displayed, then release the key Manual Response AdjustmentKey until Press Key again quicklyCalibration Calibration GroupOne-Touch Calibration Automatic self calibration due to changes in temperatureAutomatic Self Calibration MarkCalibration Test Using the Internal Mass Press and hold the CAL Key until is CCCalibration Using an External Weight Key ..............The key to store the new mass value Calibration Test Using an External WeightKey................. The key To cancel the operation Even if the AC adapter is removed,Correcting the Internal Mass Value Function Switch and Initialization Permit or InhibitKey to display Press the Print key To cancel this operation, pressInitializing the Balance Setting the Function Table Display symbol and keys Function TableKey to select a class Press Setting procedureFunction table is displayed Press Key to enter the class Key to select a item PressSetting example Details of the Function Table Data output Time/Date output Factory settingsInt ID number outputErCd 5if TimeoutAK, Error code Interface Ct5Description of the Class Environment, Display Stream mode Description of the Item Data Output ModeKey mode Auto print modes a and BStandard format Interval memory modeDescription of the Item Data Format DP Dump print formatNU numerical format KF formatMT format Data Unit Terminator Stable value Unstable valueDate CSV formatData number TimeData Format Examples Positive errorNegative error Space Stable Unstable OverloadUnits Operation Setting the timeClock and Calendar Function Confirming the timeSet the date Store Setting the dateQuitting the operation Setting the ID Number ID Number and GLP ReportKey operation Calibration report using the internal massGLP Report Commad Calibration test report using an internal massBalance returns to weighing mode after this test Calibration report using an external weight Calibration test report using an external weight When using preset target value, proceed to stepWeighing data Title block and end blockTitle block Releasing Clr or err Returns to the weighing modeData Memory Press and hold the Print key until the keyMemory full Data Memory for Weighing DataStoring the weighing data Interval memoryAdditional parameter settings, as follows Setting the function tableParameter settings for each output mode are as follows Enabling the data memory functionDeleting all memory data at one time Recalling the memory dataTransmitting all memory data at one time Transmitting the memory data Data Memory for Calibration and Calibration TestStoring the calibration and calibration test data Deleting data stored in memoryUnderhook Prior to measurement Changing the function table Density MeasurementFormula to obtain the density Density of a liquidRelation between the water temperature and density Entering the density of a liquidPress the modes Measuring the densityOutput or store Density display Turns off. lights Key to proceed to otherSub 25 pin assignments Standard Input and Output InterfaceRS-232C Interface Connection to Peripheral Equipment Connection to an AD-8121B printerConnection to a computer and the use of WinCT Using Windows Communication Tools Software WinCTUsing the WinCT software, the balance can do the following RsComCommands Command ListSettings Related to RS-232C Acknowledge Code and Error CodesControl Using CTS and RTS Command Re-zeroing the display Command ExamplesOn command turning on the balance CAL command Calibration with internal mass Error codeCommand ?PT command Net value Tare value Weighing with a tareZero Command ExecutionPT command to set a target weight of 10 g Zero display Treatment of the Balance MaintenanceError Codes Automatic response adjustment zero error Sample mass errorUnit mass error Automatic response adjustment unstable errorOther Display Asking for Repair Checking the Balance Performance and EnvironmentChecking that the balance performs properly Specifications External Dimensions Unit mmGH-08 Ethernet Interface Options and Peripheral EquipmentGH-02 USB interface AD-8121B PrinterAX-USB-9P-EX USB Converter AD-1653 Density Determination KitAD-1683 DC Static Eliminator 9970 g/cm3AX-SW128 Foot switch AX-T-314A-S External key PlugOther options Terms/Index TermsIndex 5tart Options5pd Out Tare PU5eMemo Memo
Top Page Image Contents