Invacare 1101100 Adjusting T-ARM Transfer Assists AND/OR Side Guards Figure, Arm Side Guard

Page 25

ARMS

PROCEDURE 6

5.

While holding the T-arm socket and the T-arm clamp

 

together, tighten the four (4) hex screws and washers.

 

Torque to 80-90 in./lbs.

6.

Press in on the locking lever and lift the T-arm straight

 

up and out of the T-arm socket.

T-Arm

Side Guard

7.

Repeat STEPS 3-6, if necessary until the T-arm slides

 

in the T-arm socket as desired.

8.

If necessary, install rear wheels. Refer to INSTALL-

 

ING/REMOVING REAR WHEELS in PROCEDURE

 

7 of this manual.

Socket Screws

Transfer

Assist

Bottom Clamp

A R M S

T-Arm

T-Arm Clamp

Hex Screws

Hex Screwsand Washers

and Washers

Slot

 

Locking

T-Arm Socket

Lever

FIGURE 6 - ADJUSTING T-ARM SOCKETS

ADJUSTING T-ARM TRANSFER ASSISTS AND/OR SIDE GUARDS (FIGURE 7)

1.Remove the T-arm from the wheelchair. Refer to IN- STALLING/REMOVING T-ARMS in this procedure of the manual.

2.Remove the two (2) socket screws that secure the side guard to the bottom clamp.

NOTE: Adjusting the side guards will directly affect the position of the transfer assist.

3.Perform one (1) of the following:

SMALL SIDE GUARDS - Move the bottom clamp up one (1) of two (2) mounting positions in the side guard.

LARGE SIDE GUARDS - Move the bottom clamp up one(1)ofthree(3)mountingpositionsinthesideguard.

4.Re-secure the side guard to the bottom clamp with the two (2) socket screws. Torque to 80-90 in./lbs.

FIGURE 7 - ADJUSTING T-ARM TRANSFER

ASSISTS AND/OR SIDE GUARDS

INSTALLING OPTIONAL RIGID CLOTHING GUARDS (FIGURE 8)

1.Position the threaded and unthreaded half clamps on inside and outside of the wheelchair frame.

NOTE: Make sure the threaded half clamp is on the out- side of the wheelchair frame.

2.Loosely install the washer and socket screw into the unthreaded and threaded half clamps.

3.Determine the desired rigid clothing guard position and tighten the two (2) half clamps together with the socket screw. Torque to 110-120 in./lbs.

4.Insert the rigid clothing guard into the slot on the threaded half clamp as shown in FIGURE 8.

5.Repeat STEPS 1-4 for the opposite rigid side guard.

Wheelchair

Half Clamp

Frame

 

Socket Screw

Rigid

Washer

 

Clothing

 

Guard

 

Slot

Threaded

Half Clamp

 

5. Install the T-arm onto the wheelchair. Refer to IN-

FIGURE 8 - INSTALLING OPTIONAL RIGID

STALLING/REMOVING T-ARMS in this procedure of

the manual.

CLOTHING GUARDS

25

Image 25
Contents 52,-4c E C I a L T E S R N I N GTable of Contents Labels B E L SSpyder SpecificationsI E D N E E L R I a N L E Procedure General GuidelinesN L E General Guidelines ProcedureTire Pressure I E D RE L I a NStability And Balance SAFETY/HANDLING WheelchairsCoping With Everyday Obstacles Functional Reach From a Wheelchair Stairways TiltingTransferring To And From Other Seats ESCALATORS? SorrySafety Inspection Procedure Safety Inspection ChecklistMAINTENANCE/TRANSPORTING TroubleshootingProcedure 2SAFETY Inspection Adjusting the Footrest Height Figure INSTALLING/REMOVING the Footrests FigureINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Front Riggings ProcedureInstalling Footplate Figure Procedure Front RiggingsDepth Adjustment Figure Angle Adjustment Figures 4Adjustable Footplate Heel Loop Replacement FigureImpact GUARDS/OPTIONAL Calf Strap Figure Composite FootplatesH O L S T E R Y Installing Optional Fabric Clothing Guards FigureReplacing Seat Upholstery Figure Upholstery Procedure M E Procedure FrameFOLDING/UNFOLDING the Wheelchair Figure Unfolding Details A, B and CFrame Procedure USING/STORING the Strap FigureFOLDING/UNFOLDING the Back Figure Adjusting the Back Height Figure Adjusting the Back Release Cord Tension FigureM E Back Release Cord LockINSTALLING/REMOVING T-ARMS Figure Adjusting Half ARM Height FigureAdjusting the T-ARMS Arms ProcedureFollowing Procedure ArmsInside T-Arm Set Screws Outside Post Arm Release Lever Arm PadInstalling Optional Rigid Clothing Guards Figure Adjusting T-ARM Transfer Assists AND/OR Side Guards FigureArm Side Guard Socket Screws Transfer Assist Bottom ClampAdjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureProcedure Rear Wheels A RAdjusting QUAD-RELEASE Handles Installing QUAD-RELEASE Axles FigureRear Wheels Procedure And/or Out FigureAdjusting the High/Undermount Wheel Lock REPLACING/ADJUSTING the Wheel Lock FigureReplacing the High/Undermount Wheel Lock Hex Screws High Mount Wheel LockAdjusting Anti-tippers Figure INSTALLING/ADJUSTINGInstalling Anti-tippers Figure ANTI-TIPPERSPage Warranty Limited WarrantyR R a N T Y One InvacareWay