|
|
|
|
|
| Admin |
| Administrator password. Only administrator can configure the “Advanced |
|
| Password |
| Settings” page. Password field is purposely left blank for security reason |
|
|
|
| after clicking update and saved. The maximum password length is 25 |
|
|
|
| characters. |
|
|
|
|
|
|
|
|
|
|
|
| Silence |
| This controls the silence suppression/VAD feature of G723 and G729. If set |
|
| Suppression |
| to “Yes”, when a silence is detected, small quantity of VAD packets (instead |
|
|
|
| of audio packets) will be sent during the period of no talking. If set to “No”, |
|
|
|
| this feature is disabled. |
|
|
|
|
|
|
|
|
|
|
|
| Voice Frames |
| This field contains the number of voice frames to be transmitted in a single |
|
| per TX |
| packet. When setting this value, the user should be aware of the requested |
|
|
|
| packet time (used in SDP message) as a result of configuring this parameter. |
|
|
|
| This parameter is associated with the first vocoder in the above vocoder |
|
|
|
| Preference List or the actual used payload type negotiated between the 2 |
|
|
|
| conversation parties at run time. |
|
|
|
| e.g., if the first vocoder is configured as G723 and the “Voice Frames per |
|
|
|
| TX” is set to be 2, then the “ptime” value in the SDP message of an INVITE |
|
|
|
| request will be 60ms because each G723 voice frame contains 30ms of |
|
|
|
| audio. Similarly, if this field is set to be 2 and if the first vocoder chosen is |
|
|
|
| G729 or G711 or G726, then the “ptime” value in the SDP message of an |
|
|
|
| INVITE request will be 20ms. |
|
|
|
| If the configured voice frames per TX exceeds the maximum allowed value, |
|
|
|
| the BudgeTone 200 will use and save the maximum allowed value for the |
|
|
|
| corresponding first vocoder choice. The maximum value for PCM is |
|
|
|
| 10(x10ms) frames; for G726, it is 20 (x10ms) frames; for G723, it is 32 |
|
|
|
| (x30ms) frames; for G729/G728, 64 (x10ms) and 64 (x2.5ms) frames |
|
|
|
| respectively. |
|
|
|
|
|
|
|
|
|
|
|
| Layer 3 QoS |
| This field defines the layer 3 QoS parameter which can be the value used for |
|
|
|
| IP Precedence or |
|
|
|
|
|
|
|
|
|
|
|
| Layer 2 QoS |
| This contains the value used for layer 2 VLAN tag. Default setting is |
|
|
|
| blank. |
|
|
|
|
|
|
|
|
|
|
|
| No Key Entry |
| Default is 4 seconds. |
|
| Timeout |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Use # as |
| This parameter allows users to configure the “#” key to be used as the |
|
| Send Key |
| “Send” (or “Dial”) key. If set to “Yes”, pressing this key will immediately |
|
|
|
| trigger the sending of dialed string collected so far. In this case, this key is |
|
|
|
| essentially equivalent to the “(Re)Dial” key. If set to “No”, this “#” key will |
|
|
|
| then be included as part of the dial string to be sent out. |
|
|
|
|
|
|
32