Siemens 30ISDN operating instructions Convenient and secure telephone communication Parking a call

Page 26

Convenient and secure telephone communication

Parking a call

d S04

S and b

Resuming a parked call

a

S04

S and c

You can temporarily park a call in order to

●reactivate it at a later stage

●resume it at another telephone

●unplug your telephone from one socket and plug it into another

The telephone must not be parked for more than three minutes, as otherwise the call will be disconnected.

A call is in progress.

Press the Programming key and enter the code “04“ for “Parking a call“.

The stored connection code is indicated on the display.

The connection code is a number under which the call can be parked and later resumed.

If the call is to be parked under a different connection code, the connection code must have been changed beforehand (➔ page 34).

Press the Programming key again and replace the hand- set.

The call is now parked for a maximum period of 3 minutes.

A call can only be parked, if is connected to the same S0 bus.

You can resume a parked call from the same telephone or from a different telephone (it must be connected to the same S0 bus).

Prerequisite: A call is parked and you are not conducting a call.

Handset is on-hook.

Press the Programming key and enter the code “04“ for “Parking/resuming a call“.

The connection code is indicated on the display. If the call was parked under a different connection code, change the connection code beforehand (➔ page 34).

Press the Programming key again and lift the handset. You are now re-connected to the parked caller.

You can cancel a programming procedure without making any changes by pressing the Disconnect key h !

18

Image 26

Contents Profiset 30isdn Your guide to this manual Profiset 30isdnProfiset 30isdn Profiset 30isdn Overview Profiset 30isdn Profiset 30isdn Overview Keys Location of the telephone Safety precautions and approvalSafety precautions Profiset 30isdn Approval and conformity Contents Isdn glossary IndexPutting the telephone into operation Symbols used in these operating instructionsPutting the telephone into operation Page Handset cord coiled Telephone connecting cordPutting the telephone into operation Connect the telephone Program the multiple subscriber numbers MSNs NtbaSetting the national variants PBX operation only Program the trunk codeTaking a call Putting the telephone into operation Try out the telephoneCalling another party Display-driven telephone operation SymbolsDigit display line Display Idle mode Display-driven telephone operationConnected mode 030234577 001.20 045672343Calling users On-hook dialling Outgoing and incoming callsOutgoing and incoming calls Outgoing and incoming calls Number redial automatic dialling Is displayed Call forwarding Outgoing and incoming calls Accepting a callRejecting a call Disconnect Accepting call waiting Deactivating the call signal Do not disturbOutgoing and incoming calls Call waiting Rejecting call waitingDialling a number from the call list Outgoing and incoming calls Call listRetrieving entries from the call list Storing a number from the call listInitiating a callback CallbackDeleting the call list Clearing a callback Ending a call disconnectingAccepting a callback Convenient and secure telephone communication Switching to mute consultation in the roomConvenient and secure telephone communication Activating/deactivating open listeningConvenient and secure telephone communication Parking a call Resuming a parked callPage Keypad signalling Dtmf Calls involving two or more parties Switching between two calling parties togglingCalls involving two or more parties Calling the second party consultationDisconnecting one party Three-party conferenceEnding a conference and toggling between parties Ending a conference by disconnecting a partyCalls involving two or more parties Ending a conference Exiting from a conferenceProgramming the destination dialling keys Programming keys on the telephoneProgramming keys on the telephone Programming the speed dialling keysProgramming direct station selection babyphone Description Procedure Telephone settings Quick reference for available telephone settingsQuick reference for available telephone settings Password Programming the telephone settingsProgramming the telephone settings Programming the telephone settings Ringer volume Ringer melodyS06 T 0 or Following settings are possible Call processing typeMultiple Subscriber Numbers MSN Programming the telephone settings National variants Page Date/time Call number for call forwarding unconditionalEnter the call number for call forwarding Save the setting Tariff unit factorProgramming the telephone settings Clearing the summation meter S14 TEnabling/disabling call waiting Programming the telephone settings Clearing memory Checking the settings statusDisplaying the software version Maintenance Important information for installation and operationImportant information for installation and operation Removing and inserting the labelling cardsDefault settings Technical dataThird party use/disposal Siemens Service Symptom Cause Action Isdn glossary Isdn glossaryIsdn glossary Isdn glossary Toggling d è R è R Quick reference guideQuick reference guide Quick reference for available telephone settings Index IndexTechnical data Page Siemens Aktiengesellschaft