Memorex MPH7895 manual Belt Clip Instruction, Connecting the Headset, Base Unit Power Connection

Page 12

B. WALL MOUNTING (No Standard Wall Jack)

1.Drill two holes with a vertical distance between the two marked

	positions of 3 15/16" (100 mm) as shown in Figure 6.	3 15/16”
2.	Drive a screw into each of the holes. Tighten them to the end	(100 mm)
	of the screw line, only leaving the smooth part of the screw head
	outside the wall.
	outside the wall.
3.	Hang the unit onto the screws, then slide it down firmly to	(Figure 6)
	fasten the base securely.	(Figure 6)
	fasten the base securely.

BELT CLIP INSTRUCTION

Clamp the belt clip at the back of the handset as shown in Figure 7.

Belt Clip

(Figure 7)

CONNECTING THE HEADSET

For hands free conversation, a headset (not included) is connected to the headset jack as shown in Figure 8. The handset receiver and microphone are disabled when the headset is connected.

Headset Plug (2.5mm)	Headset
	Headset
	Jack

(Figure 8)

Press the TALK button to answer or place a call using the headset. Refer to the manufacturer's headset manual for more details.

BASE UNIT POWER CONNECTION

CAUTION:

íúóáéÚÍÓÁYou must use a Class 2 Power Source 9VAC 500mA. The plug must correctly fit the unit's adapter jack.

1.Plug the adapter into a standard AC outlet.

2.Insert the small plug into the adapter jack on the rear of the base as shown in Figure 9.

11

	Page 12	7/5/01, 4:07 PM
MPH7895/04281A(English).put	Page 12	7/5/01, 4:07 PM	Adobe PageMaker 6.5C/PPC

Image 12

Contents MPH7895 Important Service Information Carton Contents Important Safety Instructions Battery Safety Instructions Installation PrecautionsFCC Notice Table of Contents Description Controls Location and FunctionHandset Controls Cordless Telephone Handset Controls Answering System Base Unit Controls Mounting Position Code FunctionDesktop USE Wall USEConnecting the Headset Base Unit Power ConnectionBelt Clip Instruction Wall Mounting No Standard Wall JackHandset Battery Installation Initial SetupSetting the DAY and Time of the Base Unit Telephone Operation If the Handset is on the Base UnitWhen the Handset is OFF the Base Unit and in Standby Mode If the Handset is OUT of the Base UnitStoring Telephone Numbers Into Memory Dialing Directory Storing Telephone Numbers Into the Speed Dialing ListDeleting Stored Telephone Numbers Deleting Single Memory LocationDeleting ALL Memory Location Dialing from the Memory Dialing DirectoryAuto Channel Scan Manual Channel ScanTo Turn Answer Mode OFF To Turn Answer Mode onAnswering Machine Operation Playing Messages Skipping MessagesPrevious Messages Stop Message PlaybackErasing ALL ICM and TWO-WAY Recordings Erasing ALL Memo MessagesErasing OGM From the Extension PhoneUsing the Handset Remote OperationCalling the Unit from a Tone Phone Voice Help MenuChanging the Password Setting the DAY and TimeSetting Answer Mode to on Setting Answer Mode to OFFCaller ID Operation Introduction to Caller ID and Call Waiting IDQuestions Answers Receiving NEW CallDeleting Single Call Record Deleting ALL Call RecordsCallback Option Summary of Function Mode HOW to Change the LanguageHOW to SET Cidcw on / OFF HOW to SET User and Neighboring Area CodeHOW to SET Ringer on / OFF HOW to SET TimeHOW to Adjust the Contrast of LCD Display LCD Display Symbols and Message Deleted Empty Data ErrorLong Distance No Calls John SmithMaximizing Battery Life MaintenanceImproving Cordless Reception Troubleshooting Symptoms Possible Solution / CausePhone answering device TAD connected with the unit Adapter Use only with Class 2 Power Source 9VAC 500 mA Technical InformationDistributed Exclusively by Memorex MPH7895 / 04281A-1