Memorex MPH7895 manual Auto Channel Scan, Manual Channel Scan

Page 17
BASE CALL
(Figure 16)
OUT OF RANGE

4.Follow steps 4-7 as described in the section Storing Telephone Numbers Into Memory to overwrite the selected entry.

MIXED MODE DIALING (Temporary Pulse to Tone Dialing)

1.If you only have pulse (rotary dialing) service in your area and want to access Tone services (Bank by Phone, etc.), ensure that the T / P (Tone / Pulse) switch is set to the Pulse position.

2.Press the TONE ( * ) button once to switch from Pulse to Tone dialing temporarily. Pulse dialing mode resumes when the call is ended.

PAUSE FUNCTION

In some cases, such as PABX or long distance service, a pause may be needed in the dialing sequence. Pressing the RE/PA button inserts a four-second delay between dialed numbers.

FLASH FUNCTION

Used to access custom calling features such as Call Waiting or Three-Way Calling provided by your local phone company. Flash can also be used to restore a dial tone to make a new call.

CHANNEL SELECTION (40 Channels)

A. AUTO CHANNEL SCAN

When you place or receive a call and handset TALK button is pressed, the unit auto-scans for a clear channel.

Once it finds a clear channel, the handset LCD Display symbol will light steadily.

B. MANUAL CHANNEL SCAN

If the existing channel becomes noisy or starts having interference, you can either move closer to the base unit or press the SCAN/PRG button on the handset until better reception is found.

OUT OF RANGE WARNING

The handset and base unit communicate up to a certain maximum range. The distance can be affected by weather, power lines, or even other cordless telephones.

If you are far away from the base unit, the handset beeps and "OUT OF RANGE" is shown on the LCD display to warn you that the background noise level is too high for proper communication between the handset and the base unit.

When you hear this sound and see the "OUT OF RANGE" display, you should move closer to the base unit. Otherwise, the call will automatically cut off after 30 seconds.

LOW BATTERY WARNING

When the handset battery voltage level is low, the handset LOW LCD Display. Return the handset on the base cradle to charge.

symbol is shown on the

PAGING FUNCTION

If you have misplaced the handset or need to alert the person nearby the handset, press the PAGE button on the base unit. Each press of

this button will activate the handset to beep for 30 seconds and LCD Display shows "BASE CALL" while it is being paged by the base unit.

NOTE: Even if the handset is in RING OFF mode, the base unit can page the handset.

16

 

Page 17

7/5/01, 4:08 PM

 

 

 

MPH7895/04281A(English).put

Adobe PageMaker 6.5C/PPC

 

 

 

 

 

 

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents MPH7895 Important Service Information Carton Contents Important Safety Instructions Installation Precautions Battery Safety InstructionsFCC Notice Table of Contents Handset Controls Cordless Telephone DescriptionControls Location and Function Handset Controls Answering System Base Unit Controls Code Function Mounting PositionDesktop USE Wall USEBase Unit Power Connection Connecting the HeadsetBelt Clip Instruction Wall Mounting No Standard Wall JackSetting the DAY and Time of the Base Unit Handset Battery InstallationInitial Setup If the Handset is on the Base Unit Telephone OperationIf the Handset is OUT of the Base Unit When the Handset is OFF the Base Unit and in Standby ModeStoring Telephone Numbers Into Memory Dialing Directory Storing Telephone Numbers Into the Speed Dialing ListDeleting Single Memory Location Deleting Stored Telephone NumbersDeleting ALL Memory Location Dialing from the Memory Dialing DirectoryManual Channel Scan Auto Channel ScanAnswering Machine Operation To Turn Answer Mode OFFTo Turn Answer Mode on Skipping Messages Playing MessagesPrevious Messages Stop Message PlaybackErasing ALL Memo Messages Erasing ALL ICM and TWO-WAY RecordingsErasing OGM From the Extension PhoneRemote Operation Using the HandsetCalling the Unit from a Tone Phone Voice Help MenuSetting the DAY and Time Changing the PasswordSetting Answer Mode to on Setting Answer Mode to OFFIntroduction to Caller ID and Call Waiting ID Caller ID OperationQuestions Answers Receiving NEW CallCallback Option Deleting Single Call RecordDeleting ALL Call Records HOW to Change the Language Summary of Function ModeHOW to SET Cidcw on / OFF HOW to SET User and Neighboring Area CodeHOW to Adjust the Contrast of LCD Display HOW to SET Ringer on / OFFHOW to SET Time Deleted Empty Data Error LCD Display Symbols and MessageLong Distance No Calls John SmithImproving Cordless Reception Maximizing Battery LifeMaintenance Symptoms Possible Solution / Cause TroubleshootingPhone answering device TAD connected with the unit Technical Information Adapter Use only with Class 2 Power Source 9VAC 500 mADistributed Exclusively by Memorex MPH7895 / 04281A-1
Top Page Image Contents