Memorex MPH7895 manual Telephone Operation, If the Handset is on the Base Unit

Page 14
(Figure 14)
CIDCW function. See
(Figure 13)

7.After two beeps, press 1 for AM, or press 2 for PM. The unit will announce the new day and time followed by a long beep and will prompt "Please enter next command."

8.Press the REMOTE button to exit the remote mode. Otherwise, the remote function will turn off automatically if not in use for 8 seconds.

TONE / PULSE SETTING

Select the appropriate dialing service by moving the T / P (Tone / Pulse) switch on the bottom of the base unit:

•(T) TONE for Tone service, or

•(P) PULSE for Rotary service.

T / P (Figure 12)

SETTING THE HANDSET RINGER

The handset ringer must be set to ring ON mode in order that to ring when receiving an incoming call. See PROGRAMMING MODE section on page 25.

SETTING USER'S AREA CODE AND NEIGHBORING AREA CODE

In order to use callback function, the user's area code and neighboring area code must be programmed. Neighboring area code is optional. See PROGRAMMING MODE section on page 24.

SETTING THE CALLER ID CALL WAITING (CIDCW) FUNCTION

The CIDCW function must be set to ON position in order to use

PROGRAMMING MODE section on page 24.

TELEPHONE OPERATION

TO PLACE A CALL IN TALK MODE

1.Press the TALK button on the handset. The LCD Display will show "TALK" and the symbol will flash while the unit

auto-scans and will light steadily when it finds a clear channel.

2.Listen for a dial tone.

3.Dial the telephone number. The phone numbers appear on the LCD Display as you enter the number.

4.When finished with your call, press the TALK button or place the handset on the base unit.

TO PLACE A CALL IN STANDBY MODE (PREDIAL MODE)

1.Ensure that the unit is in standby mode.

2.Dial the telephone number or press RE/PA button. If you

make a mistake, press VOL / button to delete the character on the left of the cursor.

3.Press C. BACK button.

4.When finished with your call, press the TALK button or place the handset on the base unit.

TO RECEIVE A CALL

NOTE: If you are expecting incoming calls, the handset must be programmed to RING ON mode. See PROGRAMMING MODE section on 25.

A. IF THE HANDSET IS ON THE BASE UNIT

1.Since the unit features "Auto-Answer", simply pick up the handset from the base cradle

when the phone rings. The LCD Display will show "TALK" and the symbol will light steadily.

2.Start your conversation.

3.When finished with your call, either press the TALK button or place the handset on the base unit.

13

 

Page 14

7/5/01, 4:07 PM

 

 

 

MPH7895/04281A(English).put

Adobe PageMaker 6.5C/PPC

 

 

 

 

 

 

 

Page 13 Page 15
Image 14
Page 13 Page 15
Contents MPH7895 Important Service Information Carton Contents Important Safety Instructions Battery Safety Instructions Installation PrecautionsFCC Notice Table of Contents Handset Controls Cordless Telephone DescriptionControls Location and Function Handset Controls Answering System Base Unit Controls Desktop USE Mounting PositionCode Function Wall USEBelt Clip Instruction Connecting the HeadsetBase Unit Power Connection Wall Mounting No Standard Wall JackSetting the DAY and Time of the Base Unit Handset Battery InstallationInitial Setup Telephone Operation If the Handset is on the Base UnitStoring Telephone Numbers Into Memory Dialing Directory When the Handset is OFF the Base Unit and in Standby ModeIf the Handset is OUT of the Base Unit Storing Telephone Numbers Into the Speed Dialing ListDeleting ALL Memory Location Deleting Stored Telephone NumbersDeleting Single Memory Location Dialing from the Memory Dialing DirectoryAuto Channel Scan Manual Channel ScanAnswering Machine Operation To Turn Answer Mode OFFTo Turn Answer Mode on Previous Messages Playing MessagesSkipping Messages Stop Message PlaybackErasing OGM Erasing ALL ICM and TWO-WAY RecordingsErasing ALL Memo Messages From the Extension PhoneCalling the Unit from a Tone Phone Using the HandsetRemote Operation Voice Help MenuSetting Answer Mode to on Changing the PasswordSetting the DAY and Time Setting Answer Mode to OFFQuestions Answers Caller ID OperationIntroduction to Caller ID and Call Waiting ID Receiving NEW CallCallback Option Deleting Single Call RecordDeleting ALL Call Records HOW to SET Cidcw on / OFF Summary of Function ModeHOW to Change the Language HOW to SET User and Neighboring Area CodeHOW to Adjust the Contrast of LCD Display HOW to SET Ringer on / OFFHOW to SET Time Long Distance No Calls LCD Display Symbols and MessageDeleted Empty Data Error John SmithImproving Cordless Reception Maximizing Battery LifeMaintenance Troubleshooting Symptoms Possible Solution / CausePhone answering device TAD connected with the unit Adapter Use only with Class 2 Power Source 9VAC 500 mA Technical InformationDistributed Exclusively by Memorex MPH7895 / 04281A-1
Top Page Image Contents