Telular SX5T CDMA2000, SX5T-505C, SX5T-535C, SX5T-500C To connect an SX5T model with a BBU

Page 8

Connecting an SX5T Model With a BBU (Backup Battery Unit)

Your SX5T has either a Power Supply (part #74007301) or a Battery Backup Unit (BBU; part #74006803).

If your model has a BBU, it is shipped with the battery disconnected to prevent if from being prematurely drained. The BBU must not be connected to a SX5T or toAC power when you connect or replace the battery. Connecting the wrong wires to the battery terminals may cause severe damage to the device.

To connect an SX5T model with a BBU:

1.Make sure the BBU is disconnected from the SX5T and the AC power cord.

2.Unlatch the battery compartment cover by using a coin to rotate its latch to the open position.

3.Remove the cover.

4.Connect the black wire (-) in the battery compartment to the black terminal (-) on the battery - see Figure 6.

5.Connect the red wire (+) in the battery compartment to the red terminal (+) on the battery - see Figure 6.

6.Insert the battery into the battery compartment.

7.Reattach the compartment cover and secure it with the cover latch.

8.Insert the barrel connector of the Power Supply and Battery Backup Unit’s cord into the SX5T’s Power Input - see Figure 3 on page 2.

9.Connect the AC power cord to the Power Supply and Battery Backup Unit, then plug it into a power outlet - see Figure 3 on page 2.

10.Press the Battery Power Switch on the BBU to the ON ( / right) position.

11.Slide the Power Switch on the SX5T to the ON (right) position.

12.Check the cellular signal strength and move the unit until you achieve the best signal possible - see LED Status Indicators on page 8 for more information.

Figure 6 – Connecting the battery.

Red Wire (+)

Black Wire (-)

Black Terminal (-)

Battery Compartment

Red Terminal (-)

Phonecell® SX5T CDMA2000

4

User Manual

Image 8

Contents Phonecell SX5T CDMA2000 Contents Terms and Conditions for USE of Phonecell Products Product Telular CorporationTechnical Support Corporate HeadquartersTable of Contents Setup Ruim Card Installation Ruim Model OnlyHint Connecting an SX5T Model With a Power SupplyTo connect an SX5T model with a Power Supply Emergency Batteries To install emergency batteriesBattery Operation Connecting an SX5T Model With a BBU Backup Battery Unit To connect an SX5T model with a BBUSX5T Location and Installation Wall MountingConnectors GPS Antenna Mounting optional on SX5T-505C/-535C onlyDirect Connection Phone, Fax and Data Connection via Wall JacksLED Status Indicators Signal Strength LEDsGetting to Know Your SX5T LED ColorCallActivity Indicator LED Color Description Important Dial TonesUsing the SX5T Using In-Call FeaturesMaking Calls Receiving CallsAccessing Your Voicemail Using Call ForwardingMaking a Three-Way Call Press #Adjusting Your Phone’s Settings Volume LevelEntering Configuration Mode Changing the Lock CodeAuto-Send Delay Frequently Dialed Numbers Zero Delay DialingAudio Line Level Call BarringIndex * number # Where the options are as follows From Configuration Mode, press #Call Restrict SX5T-500C only Dial Tone After Remote Disconnect DtardYou would press # # from Configuration mode HotlineOne-Minute Alert TTY UseRestore User Defaults From Configuration Mode, press # Or 1 # , whereVoicemail Number One-Touch Voicemail RetrievalUsing a Fax Machine With Your SX5T Using Additional Hardware DevicesUsing an External Answering Machine Windows XP/Windows 2000 Setup for Data & PC Fax Press # Lock codeClick on Add… Phonecell SX5T CDMA2000 Select the 19200 bps Modem and click on Properties Control Panel System Hardware Device Manager Ports tab Phonecell SX5T CDMA2000 Windows 98 Setup for Data & PC Fax Select Standard 19200 bps Modem and click on Properties Phonecell SX5T CDMA2000 Phonecell SX5T CDMA2000 Choose Fax Mode Sending/Receiving a PC FaxSet Your Computer’s Port and Modem Speeds for PC Fax Choose the SX5T’s Fax PortSending/Receiving 1X Data Set Your Computer’s Port and Modem Speeds for 1X DataChoose the SX5T’s Data Port To Send or Receive 1X DataSending/Receiving Circuit Switched Data Choose Data ModeSet the SX5T’s Baud Rate for Circuit Switched Data Back to Voice mode Press #Advanced Programming Settings Entering Configuration Mode Advanced SettingsOn-Hook Idle Voltage Level Line ReversalRing Frequency Audio Input ImpedanceDisconnect Pulse Dial Tone Frequency SX5T-500C onlyDisconnect Tone Caller ID Display Setting SX5T-500CLine Alert Cadence Metering Pulse High Gain/Low Gain Local Metering Pulse Override/Polarity Reversal SX5T-500CSX5T Troubleshooting No PowerUnable to Receive Calls Unable to Make CallsSafety Information Conformance StatementsDriving Exposure to Electronic DevicesAircraft ChildrenPatents TrademarksPhonecell SX5T CDMA2000 Telular Corporation, all rights reserved

CDMA SX5T-500C, SX5T CDMA2000, SX5T-505C, SX5T-535C, SX5T-500C, SX5T CDMA specifications

Telular's SX5T CDMA device line represents a significant advancement in wireless communications technology, primarily designed for use in Automatic Meter Reading (AMR), asset tracking, and telemetry applications. The SX5T series includes several models, each with unique characteristics that cater to varying customer needs within the CDMA2000 framework.

One of the standout models, the SX5T CDMA, leverages CDMA2000 technology for robust and reliable wireless connectivity. This technology offers greater capacity and improved voice quality compared to earlier generation systems. The SX5T CDMA is particularly noted for its flexibility in deployment, making it an ideal choice for industries requiring seamless communication solutions.

Another variant, the SX5T-505C, builds upon the solid foundation of the SX5T CDMA, incorporating enhanced features for more demanding applications. This model includes advanced remote management capabilities, allowing users to monitor and configure devices remotely, which can lead to significant cost savings and operational efficiencies.

The SX5T-535C model is designed with increased durability in mind, making it suitable for harsh environmental conditions. It boasts high-quality build materials and design, ensuring longevity and dependable performance even in the most challenging scenarios.

For a more budget-conscious option, the SX5T-500C provides essential functionality at a competitive price point. This model delivers reliable performance for basic telemetry applications, making it an optimal choice for smaller businesses or projects with tighter budgets.

All models within the SX5T series operate on the CDMA SX5T-500C standard, offering high-speed data transmission, which is crucial for applications that require real-time information transfer. The devices support seamless integration with existing infrastructure, ensuring that they can be easily incorporated into various communication systems.

Features common across the SX5T series include low power consumption, comprehensive security protocols, and extensive customization options, allowing users to adapt the devices for specific application requirements. These attributes, combined with Telular's commitment to innovation, position the SX5T CDMA product line as a leading choice for businesses looking to enhance their telemetry solutions and streamline operations in an ever-evolving technological landscape.