Sanyo CLT-J30 Replacing a directory entry with a Caller ID entry, Changing a stored number

Page 21

DIRECTORY

9. Press the number (0 – 6) or use CID/VOL or to select the desired animation. The selected animation will be displayed when the incoming call matches with the number you stored.

10.Press MEM again. “RINGER TONE 1” shows on screen.

11.Press 1-3 or 1-6 depending on the model or use CID/VOL or to select the desired ringer tone (6 melody ring tones available for J50/J60 or 3 tones for J30/J40/J40(BK)). The selected ringer tone will be heard when the incoming call matches with the number you stored.

12.Press MEM again. “VIP 1YES 2 NO” shows on screen.

13. Press the number (1 – 2) or use CID/VOL or to select the desired status. Once tagged as VIP, this caller can bypass the DND feature.

14.Press MEM again to store the number to memory. If you are replacing a number, “REPLACE MEMO?” shows on screen. Press MEM again to confirm, or press *TONE/EXIT to return to standby mode.

To view your directory, press MEM and use CID/VOL	or	or the
number (0-9) to scroll.

Replacing a directory entry with a Caller ID entry

Use the same procedure as for storing Caller ID entries in the directory

Changing a stored number

Use the same procedure as for storing a number in the directory

Making calls from the directory

1.Make sure the phone is ON by pressing TALK/CALL BACK.

2.Press MEM.

3.Press the number (0 - 9) for the desired memory location. The number dials automatically.

Or:

1.Make sure the phone is OFF (not in TALK mode).

2.Press MEM.

3. Press the number (0-9) or use CID/VOL	or	to select the
desired number.

4.Press TALK/CALL BACK, the number will be dialed automatically.

21

Image 21

Contents Sanyo Canada Inc CLT-J30Table of Contents Recycling NICKEL-METAL Hydride Batteries Other features Main Features GHz TechnologyIntroduction Compander Plus Noise ReductionChecking package contents Getting StartedModular jack Battery setup Tone/pulse settingTelephone line connection Digital Security System Mounting on a wallHandset Names and ControlsBase Unit Area code setting Language settingInitial Programming Press FLASH/PROG until 1 ENG 2 FRA 3 ESP shows on screenLCD contrast DND settingIdle animation Resetting to defaultRinger switch Volume adjustmentBasics Receiving a callPress TALK/CALL Back Changing the pre-dial number Pre-dialing up to 32 digitsRedialing Fast redialing Press TALK/CALL BackVoice mail indicator Low battery warningHandset locator Paging function Mute keyCaller ID Features Caller ID with Call WaitingCaller ID list Reviewing Caller ID list Format Caller ID numbersStoring Caller ID entries in the directory Dialing a Caller ID number Deleting entries from the Caller list Deleting the displayed entryDeleting all entries Store a number in the directory DirectoryReplacing a directory entry with a Caller ID entry Changing a stored numberMaking calls from the directory Reviewing and deleting directory contents Chain dialing from the directoryNumber for Memory Location Battery replacement and handling Changing the BatteryPower Failure Changing the Face PlatesRecycling NICKEL-METAL Hydride Batteries Headset Jack and Belt Clip Light SignalsLCD Screen Messages ErrorTroubleshooting Sound SignalsCaller ID error message No displayHandset does not ring Dial tone is OK, but cannot dial outYou experience static, noise, or fading in and out Phone beepsCauses of poor reception MaintenanceKeep the contacts clean Maximize Battery PerformanceRefresh battery Charge it for a full 12 hoursTechnical Information Technical Information What is not Covered Sanyo Comfort WarrantyBetween 830 am 700 pm EST SOS Help Line