Spectrum Brands SP-550 manual Programming Voice Mail Dialing, Test the program

Page 34

Programming Voice Mail

(Administrator Programmable Only)

To program the SpectrumPLUSTM one touch “MESSAGE WAITING” speed dial key, follow these programming instructions.

Programming Voice Mail Dialing
1.	Press and hold the “STORE” key to activate
1.	Press and hold the “STORE” key to activate				12/01	PM	12:00
	Administrator mode.		555-1212
2.	Press the “STORE” key multiple times until		555-1212
2.	Press the “STORE” key multiple times until			VOICE MAIL NO.
	“VOICE MAIL NO.” is displayed on the LCD			VOICE MAIL NO.
	screen.
3.	Enter the voice mail number. The area code is
	not required if AREA CODE is programmed
	not required if AREA CODE is programmed
	into memory.
4.	Press the “STORE” key to store the voice mail
4.	Press the “STORE” key to store the voice mail				12/01	PM	12:00
	number into the VOICE MAIL memory key.				12/01	PM	12:00
	number into the VOICE MAIL memory key.
5.	Enter the “PIN NUMBER”, up to 8 digits. The		- - - - - - - -
5.	Enter the “PIN NUMBER”, up to 8 digits. The
	PIN characters will not be displayed.				PIN NUMBER
6.	Enter the “SECONDS OF WAIT?”, up to 99
	seconds.
7.	To exit the program mode, press “DISC” or
7.	To exit the program mode, press “DISC” or
	continue to the end of programming by pressing
	the “STORE” key multiple times until the dis-
	the “STORE” key multiple times until the dis-				12/01		12:00
	play reads “All Setup OK”.				12/01	PM	12:00
	play reads “All Setup OK”.
Test the program			05
Test the program			SECOND OF WAIT?

After programming voice mail, test the program by placing a voice mail into the voice mail messaging system. Then, press the key located on the base unit (when in OFF HOOK position) and dial the pre- programmed numbering sequence. The “SECONDS OF WAIT” may need to be increased if the voice mail was not retrieved.

33

Image 34

Contents Page Headset Feature Installing a HeadsetUsing a Headset Placing/Answering a Call Using the Headset On/Off FeatureThis page is intentionally left blank Page Important Safety Instructions FCC Part 15 Compliance DOC Notice and Load Number Statement Consumer Information Page Page TOP Panel Page Bottom Panel Page Parts Check List Power Adapter Line Connection 120V AC Outlet Recovery Power Adapter providedConnector Configuration Power Adapter Phone ConnectionInstalling The Wall Power Adapter optional Completing the Power InstallationConnecting the Handset Cord Installing the KeycapsWall Mounting the SpectrumPLUSTM Telephone Desk MountingMessage Waiting Light Indicator Low Voltage LED Switch System Hold Feature Option Switch Administrator FeatureProgramming Set Up Of the SpectrumPLUSTM Telephone Voice Mail no PIN Number Second of WAIT? ALL Setup OKUsers Quick Program Guide for the SpectrumPLUSTM Telephone Live Dialpad Feature Administrator Programmable OnlyRestrict 1+ Feature Using a Flash When Dialing Programming Flash Timing into MemoryProgramming Flash Timing Programming Example for 100mSProgramming Pause Timing Four ExamplesProgramming a Pause into Speed Dial Memory Using a Pause when DialingTo Program a Timed Pause To Set Up The Access Number Programming the Access Number into MemoryTo Delete The Access Code Programming the Area Code into Memory Programming the Area Code into MemoryProgramming Voice Mail Voice Mail no PIN Number Second of WAIT?Programming Voice Mail Dialing Test the programAdministrator Programmable Only Manual Entry of Characters To Program Speed Dial LocationsTo Verify Speed Dial Programming To Verify Speed Dial LocationsManual Entry From Keypad Guide Press Once Twice Three Four Five Times Six TimesLOW Volt MW Using a Headset LCD Backlighting Display Information Management KeysLCD Contrast Feature 4-step LCD Call Record DisplayLCD Caller ID* Display Featured Icons 12/01 PM1200LCD Caller ID* Display Information Management Keys 12/01 PM1226 LCD Caller ID Display Information when On Hook with Messages LCD Caller ID* Display Information when Dialing 7196388821 022 PhBook Delete DialPM1200 Type II Caller Identification Caller ID Display Type Incoming Call Waiting CWSetting Date & Time Automatically Phone Book Storage Capacity Scrolling For The Most Current Caller ID Records Scrolling and Call Back FeatureScrolling For Stored Records Scrolling For The Oldest Caller ID Re- cordsDelete All Stored Call Records Adding a Phonebook Record From a Caller ID Record Adding a Caller Record To The PhonebookAdding a Phonebook Record Manually Manually Adding a Phonebook Record Into MemoryHyperlink to a Stored Record Dialing From the Phonebook DirectoryTo Dial From the Phonebook Directory Call Record Editing Prior to Dialing Invalid Entry Display Line Error DisplayOther LCD Displays No Calls Display PhoneBook Full DisplayHold Key Indicators Speaker Line IndicatorsHeadset Key Indicators Placing a Call Using Speakerphone Using the Data Port Using the Hold Feature Using The Mute Feature Using the Redial Feature Using The Disconnect Feature Key Handset Volume Control Page Page To Place An Order Parts ListPart List Description Number Price Statement of Limited Warranty