Spectrum Brands SP-550 manual Programming Flash Timing, Programming Example for 100mS

Page 28

Programming Flash Timing

(Administrator Programmable Only)

Flash timing can be programmed for different timing options listed below.

1.Press and hold the “STORE” key for 6 seconds to enter set up.

2.Press the “STORE” key multiple times until the LCD display reads “FLASH TIME SET”.

3.Enter the flash timing to be stored into memory using the keypad by pressing the following keys on the keypad in the order shown. The keypad entry will be displayed on the LCD Screen.

For 100mS press "1" "0" "0" on the keypad.

For 200mS press "2" "0" "0" on the keypad.

For 300mS press "3" "0" "0" on the keypad.

For 400mS press "4" "0" "0" on the keypad.

For 500mS press "5" "0" "0" on the keypad. !

For 600mS press "6" "0" "0" on the keypad.

For 700mS press "7" "0" "0" on the keypad.

For 800mS press "8" "0" "0" on the keypad.

For 900mS press "9" "0" "0" on the keypad. For 1000mS press "1" "0" "0" "0" on the keypad.

Note: Programming can only be performed when phone is on-hook

4. To exit the program mode, press “DISC” or continue to the end of programming by pressing the “STORE” key multiple times until the display reads “All Setup OK”.

5.To confirm the flash timing programmed in memory, repeat the Administrator programming sequence to see flash timing display.

Programming Example for 100mS

Press “STORE” for 6 seconds, Press “STORE” again until LCD reads “ “FLASH TIME SET”. Enter digits “100” from the keypad. Press “STORE” to enter the timing into memory.

!

NOTE: The Flash Timing factory default is 600mS

27

Image 28
Contents Page Headset Feature Installing a HeadsetUsing a Headset Placing/Answering a Call Using the Headset On/Off FeatureThis page is intentionally left blank Page Important Safety Instructions FCC Part 15 Compliance DOC Notice and Load Number Statement Consumer Information Page Page TOP Panel Page Bottom Panel Page Parts Check List 120V AC Outlet Recovery Power Adapter provided Connector ConfigurationPower Adapter Line Connection Power Adapter Phone ConnectionInstalling The Wall Power Adapter optional Completing the Power InstallationConnecting the Handset Cord Installing the KeycapsWall Mounting the SpectrumPLUSTM Telephone Desk MountingMessage Waiting Light Indicator Low Voltage LED Switch System Hold Feature Option Switch Administrator FeatureProgramming Set Up Of the SpectrumPLUSTM Telephone Voice Mail no PIN Number Second of WAIT? ALL Setup OKUsers Quick Program Guide for the SpectrumPLUSTM Telephone Live Dialpad Feature Administrator Programmable OnlyRestrict 1+ Feature Using a Flash When Dialing Programming Flash Timing into MemoryProgramming Flash Timing Programming Example for 100mSProgramming Pause Timing Four ExamplesProgramming a Pause into Speed Dial Memory Using a Pause when DialingTo Program a Timed Pause To Set Up The Access Number Programming the Access Number into MemoryTo Delete The Access Code Programming the Area Code into Memory Programming the Area Code into MemoryProgramming Voice Mail Voice Mail no PIN Number Second of WAIT?Programming Voice Mail Dialing Test the programAdministrator Programmable Only Manual Entry of Characters To Program Speed Dial LocationsTo Verify Speed Dial Programming To Verify Speed Dial LocationsManual Entry From Keypad Guide Press Once Twice Three Four Five Times Six TimesLOW Volt MW Using a Headset LCD Backlighting Display Information Management KeysLCD Contrast Feature 4-step LCD Call Record DisplayLCD Caller ID* Display Featured Icons 12/01 PM1200LCD Caller ID* Display Information Management Keys 12/01 PM1226 LCD Caller ID Display Information when On Hook with Messages LCD Caller ID* Display Information when Dialing 7196388821 022 PhBook Delete DialPM1200 Type II Caller Identification Caller ID Display Type Incoming Call Waiting CWSetting Date & Time Automatically Phone Book Storage Capacity Scrolling and Call Back Feature Scrolling For Stored RecordsScrolling For The Most Current Caller ID Records Scrolling For The Oldest Caller ID Re- cordsDelete All Stored Call Records Adding a Phonebook Record From a Caller ID Record Adding a Caller Record To The PhonebookAdding a Phonebook Record Manually Manually Adding a Phonebook Record Into MemoryHyperlink to a Stored Record Dialing From the Phonebook DirectoryTo Dial From the Phonebook Directory Call Record Editing Prior to Dialing Line Error Display Other LCD Displays No Calls DisplayInvalid Entry Display PhoneBook Full DisplayHold Key Indicators Speaker Line IndicatorsHeadset Key Indicators Placing a Call Using Speakerphone Using the Data Port Using the Hold Feature Using The Mute Feature Using the Redial Feature Using The Disconnect Feature Key Handset Volume Control Page Page To Place An Order Parts ListPart List Description Number Price Statement of Limited Warranty