AT&T 5845 user manual About Handset Registration, Register an additional HandsetModel 5800 handset

Page 8

5840_CIB_2ATT 2003.3.5 6:11 PM Page 4

About Handset Registration

1The cordless handsets that came with your system are automatically registered as Handset 1,and Handset 2.There is no need to re-register.

2You may register up to a total of six Expansion Handsets to this telepnone system(Model 5800 handset Sold Separately).

3Additional handsets will be assigned Handset 3,handset 4,Handset5, and Handset 6.

4When you install the handset battery pack,the handset will display SEARCHING FOR BASE (if it’s registered) or ENTER BASE ID (If it has not been registered).

Register an additional Handset(Model 5800 handset)

1Make sure the handset battery pack has been charged for at least 12 hours and that the power cord is plugged into the base unit.

2At the base display press softkey.

3Use to select DISPLAY BASE-ID.

4Press .The base screen will display the 15 digit Base ID code for approximately 30 seconds,the return to the idle screen.

5Using the handset keypad,enter the 15 digit base ID code(including

# or *).

6Use the softkey to select OK.The screen displays PLEASE WAIT!! and then SEARCHING FOR BASE.

7After about 45 seconds the handset should find the base,The screen will display the appropriate handset and it is ready for use.if the handset displays BASE BUSY TRY THE LATER,the base is in use.

5

Image 8

Contents With Caller ID/Call Waiting Part 1 Important Product Information5840CIB2ATT 2003.3.5 611 PM Contents Parts List Before YOU Begin About Adding Handsets About Caller Identification Caller ID About the Calls Log Connect the telephone line cord Connect the power cord InstallationTable/Desk Installation Check for dial tone Install the handset batteryCharge the handset battery About Handset Registration Register an additional HandsetModel 5800 handsetWall Installation Follow Steps 3-5 in Table/Desktop InstallationSpare Battery/Power Failure Backup Belt Clip HeadsetSet Time Feature Setup HandsetFeature Setup Menu Clock Mode ¥NOTE The mid-boost setting is hearing-aid compatible Sound SelectRinger Volume Ringer Melody Vibrate Control Low Batt Tone Range Tone Keypad Tone Set Contrast Language Setting Feature Setup Base Ringer Melody Dial Mode Tone/Pulse Contrast Language Telephone Operation Make a CallAnswer a Call At the HandsetBase Speaker VolumeHandset Switch Between Handset and Speakerphone Handset SpeakerphoneMake a Call Answer a CallBase Speakerphone Dialing OptionsDelete a Redial Number RedialSave a Redial Number Flash/Call Waiting BaseMute Hold Temporary Tone Dialing Display Screen Messages Screen Displays WhenHandset Icons This Icon IndicatesLight Status Indicates Base IconsBase Lights Tones and What They Mean Tone IndicatesThree quick beeps One beepIntercom Operation Intercom CallsAnswer an Incoming Call While on an Intercom Call Answering IntercomEnd Intercom Blind Call Transfer Announced Call TransferFrom the Handset From the BaseConference Calling Phone Book Store a Number and Name in Phone BookKeypad Characters Dial a Number in Phone Book Edit a Number/Name in Phone Book Delete a Number/Name in Phone Book Caller ID Operation Review Calls Log Store Record in Phone BookDisplay Dial Removing All Records Remove Call RecordsRemoving a Specific Call Record Audible Indicators Answering System Operation AT the BaseTurn Answering System On/Off Set the ClockAbout Mailboxes About AnnouncementsRecord Your Announcement AnnouncementAnswering System Feature Setup Feature Summary Delete Messages Listen to, Save & Delete MessagesPlay Messages Adjust Playback Volume Call Screening/InterceptRecord a Memo Message Window Display Window Displays WhenConnect with the Answering System Voice MenuRemote Access Commands Function CommandBattery Life Battery IndicatorCharge the Handset Battery Pack BatteriesSpare Battery Replace the Handset Battery Pack Problem SolutionProblemsolution Case of DifficultyIf your handset dis- plays Enter Base ID or no Base SUB If you hear noise or interference when using the phoneTo re-initialize the handset and base Problem Solution If the phone does not ring when you receive a callIf your telephone MisdialsCaller ID If the caller’s name or phone number is not displayedAnswering System If messages areIncomplete If callers are unable to leave messages in Mailbox 2 orClear If your outgoingAnnouncement isn’t Default Settings Default SettingsFunction Default Setting Announce OnlyTechnical Specifications Technical SpecificationsIndex 5840CIB2ATT 2003.3.5 612 PM 5840CIB2ATT 2003.3.5 612 PM