AT&T TL74458, TL74308, TL74358, TL74408, TL 74208, TL74258 user manual Message counter displays

Page 66

Answering system operation

Message counter

BASE

MSG1#

Message counter displays

The message counter usually displays the total number of answering system messages. See the table below for other message counter displays.

Message counter displays

0	No messages.
0 (flashing)	The clock needs to be set (page 51).

1-99	Total number of messages and memos,
	or message number currently playing.

1-99 (flashing)	Total number of messages and memos.
	The number flashes when there are new
	(un-reviewed) messages.
	After a power failure, the number in the
	message counter will flash to indicate
	the clock needs to be set.

10-99	Current remote access code while
	setting (page 57).

1-99 (counting)	Elapsed time while recording a memo
	(page 60) or announcement up to 90
	seconds (page 53).

99 (flashing)	A memo recording is more than 99
	seconds.
F (flashing)	Memory is full. Messages must be
	deleted before new messages can be
	recorded.

--	System is answering a call, being
	accessed remotely, or the clock is being
	set.

-- (flashing)	System is being setup, initialized or
	messages are being deleted.

02, 04, 06, tS Displayed while setting the number of

	rings (page 56).

1-8	Displayed for two seconds while
	telephone base speaker volume is being
	adjusted.

61

Image 66

Contents Page Congratulations On purchasing your new AT&T productParts checklist Table of contents TL74108/TL74208/TL74308 TL74408/TL74258/TL74358 TL74458Appendix G Quick reference guide handset PHONE/FLASHHandset LOCATOR/INTERCOM While phone is idle Volume PressQuick reference guide telephone base Disp Dial PressInstallation preparation Avoid placing the telephone base too close toAdditional handsets optional Add new handsets to make your telephone more versatile seeBackup battery installation and use not included Base Check AC PowerTelephone base installation Telephone base installationCharger installation Handset battery installation & charging This Side UPInstallation options Desktop to wall mount installationInstallation options Wall mount to desktop installation Installation options Belt clip & optional headset To attach the belt clipTo remove the belt clip Basic operation Using the telephone baseOn-hook dialing predialing Using a cordless handset Press Speaker or Disp Dial to dialClearspeakTM dial-in-base speakerphone Handset speakerphoneAuto off Last number redial Press Speaker or Disp Dial to dial the displayed numberHandset locator Press Handset LOCATOR/INTERCOM onVolume control Options while on callsCall waiting To un-mute the call on a cordless handset MuteTo mute the call on a cordless handset To mute the call on the telephone baseLast number redial Using a cordless handset Directory Using a cordless handsetCaller ID history Using a cordless handset Chain dialingIntercom To end the intercom callUnable to Call TRY Again Call transfer using intercom PHONE/FLASH, or INTCall transfer using intercom Handset settings Ringer volume Ringer toneKey tone LanguageVisual message waiting voicemail indicator To clear voicemail indicationTemporary ring silencing Telephone base settings Ringer Volume Ringer Tone KEY Tone Language CLR Voice Mail Memory capacity DirectoryShared directory Exiting the directoryNew directory entries Press MENU/SELECTEnter Name Directory Call LOG Enter Name To review directory entries Using a cordless handset Directory reviewDirectory search To search by nameTo edit an entry Using a cordless handset To dial, delete or edit entriesDisplay dial Press MENU/SELECT. You will be prompted to Edit NameCaller ID operation Information about caller ID with call waitingHow the caller ID history works Handset screen displayScreen display of the telephone base Missed calls indicator Memory matchTo review caller ID history Using a cordless handset Caller ID historyTo dial from caller ID history Using a cordless handset Other options About the answering system Answering system and voicemailVoice prompts Day & time announcement To check day & timeTo set day & time Answering system mode Call screening at the telephone baseCall intercept Outgoing announcements To play your current outgoing announcementTo record a new outgoing announcement To delete your outgoing announcement Answering system setup Number of rings Remote access code Call screeningMessage alert tone Temporarily turning off the message alert toneMessage playback Options during playbackTo delete all old messages Recording & playing memos To play back a memoMessage counter displays Message counter displaysRemote access Remote commandsRemote access Handset alert tones Screen icons & alert tonesScreen icons & alert tones Screen iconsIndicator lights Indicator lightsLighted display Lighted keypad Telephone base and handset display screen messages Screen display messagesUnable to Call Adding and registering handsets To register a handset to your telephone baseReplacing a handset You may need to de-register your handsets ifTaking care of your telephone MaintenanceCleaning your telephone Avoid waterImportant safety information Especially about cordless telephones Precautions for users of implanted cardiac pacemakers Especially about telephones answering systemsFCC Part 68 and Acta Industry Canada FCC Part Limited warranty Limited warranty Limited warranty Technical specifications GHz digital spread spectrum frequency hopping technologyTelephone operating range Troubleshooting If you are on a call during an AC power failure, using This Troubleshooting guide Please refer to the Battery installation and chargingTroubleshooting Troubleshooting Troubleshooting Day not set System does not respond to remote commands Index Index Remote access wallet card Action Remote command