AT&T E5909B user manual My Caller ID is

Page 54

Appendix

Troubleshooting

The CHARGING

• Clean the cordless handset and charging contacts on the charger

each month using a pencil eraser or cloth.

light is off.

 

 

• Make sure the power and line cords are plugged in correctly and

 

securely.

 

• Unplug the unit’s electrical power. Wait for 15 seconds, then plug it

 

back in. Allow up to one minute for the cordless handset and tele-

 

phone base to reset.

 

• Your telephone might be malfunctioning. Please refer to the Warranty

 

section of this user’s manual for further instruction.

 

 

My Caller ID is

• Caller ID is a subscription service. You must subscribe to this service

not working.

from your local telephone company for this feature to work on your

 

phone.

System does

• Your caller must be calling from an area that supports caller ID.

not receive CID

• Both you and your caller’s telephone companies must use caller ID

or system does

compatible equipment.

not display

 

CID during Call

 

Waiting.

 

 

 

Incomplete

• If a caller leaves a very long message, part of it may be lost when the

messages.

system disconnects the call after 4 minutes.

 

• If the caller pauses for more than 7 seconds, the system stops

 

recording and disconnects the call.

 

• If the system’s memory becomes full during a message, the system

 

stops recording and disconnects the call.

 

• If the the caller's voice is very soft, the system may stop recording

 

and disconnects the call.

 

 

Difficulty hear-

• Press VOLUME ^to increase speaker volume.

ing messages.

• Remove any stickers that may have come on your telephone

 

base and/or handset when you purchased it, they may be

 

obstructing your messages when you play them.

System does not answer after correct number of rings.

•Make sure that the answering system is on (see page 36).

•If Toll Saver is activated, the number of rings changes to 2 when there are new messages waiting (see page 39).

•In some cases, the system may be affected by the ringing system used by the local telephone company.

•If the memory is full or the system is off, the system will answer after 10 rings.

50

Page 53 Page 55
Image 54
Page 53 Page 55
Contents GHz Corded/Cordless Telephone/Answering System E5909B Need HELP? Information about Caller ID with Call Waiting See Table of contents GHz Corded/Cordless Telephone/Answering System E5909BQuick reference guide Menu Press to customize the telephone’s operation see Ringer Volume Set switch on sideBase Off, Low, High. see Skip Press to skip message seeBase handset Handset cord Telephone base Parts checklistTelephone line cords 1 long, 1 short Charger power Adapters Belt clip CordlessBefore you begin About Caller IdentificationTelephone operating range Telephone base installation Power adapterPlug the large Battery installation & charging Wall mounting Lock in placeSqueeze to open hinged wall mount Install belt clip as shown below if desired Belt clip & optional headsetHandset settings Choose handset languageSet handset date and time Set handset ringer volume Set handset ringer toneChoose base ringer volume Base settingsChoose dial mode Choose base languageLast number redial Basic cordless handset operationMaking and answering calls Ring silencingBasic base operation Handset locatorRedial Options while on calls Temporary tone dialing Way conference callsPhone Hold INT Intercom Call transfer Call transferHandling incoming calls Intercom callsIntercom calls INT Press INT/DELETE to page basePHONE/FLASH Intercom calls Directories Directories handset and baseTo create a Speed Dial entry See Steps 4-7 on pagesTo edit or delete a Speed Dial number To create a directory entryTo call a Speed Dial number Directory dialingEntering names into directories To enter a nameOptions while entering names Options while entering numbers Entering phone number and assigning distinctive ringTo enter a number To assign a distinctive ring cordless handset onlyTo search alphabetically Directory searchTo browse through the directory To call a displayed numberTo edit an entry To copy, edit or delete an entryTo make an entry a Speed Dial entry cordless handset only To delete an entryHow Caller ID works Caller ID and Call Waiting FunctionsNot revealed at callers request Contrast Adjustment base onlyOn-Screen Message Reason To determine the callers nameCID memory Memory CapacityReviewing the CID Memory Dialing from CID Memory Storing a record from the CID Memory into the directoryDeleting a number from the CID Memory Deleting all CID records BaseCordless handset Call waiting Message capacity Press again to quit see Press to review or set clock seeTo check day and time Day and time announcementsTo set day and time Press ClockTo play your outgoing announcement To record your outgoing announcementTo delete your outgoing announcement Changing feature options Feature optionsOptions during playback Message playbackAnnouncements To delete all messagesTo play back a memo Recording and playing memosTo record a memo BeepMessage counter displays Remote access Display screen messages, lights and tones Screen display messagesIndicator lights Alert tonesTroubleshooting My telephone does not work at allBatteries will not hold a charge Hear noise My cordless handset does not ring when I receive a call My Caller ID is CL flashes Important safety instructions Especially About Cordless Telephones Precautions for Users of Implanted Cardiac Pacemakers Especially About Telephones Answering SystemsFCC part 68 and Acta FCC part Limited warranty Limited warranty Please retain your receipt as your proof of purchase Index Technical specifications Remote access wallet card Cut along dotted lineFold card here
Top Page Image Contents