DKS Enterprises 1815, 1803PC, 1817 owner manual Main Terminal Description

Page 21

2.1 MAIN TERMINAL DESCRIPTION

TERMINAL

DESCRIPTION

 

 

1

Phone Line Connection – 800 ft. maximum with 24 AWG wire; 1600 ft. maximum with 22 AWG wire.

 

 

2

Phone Line Connection – 800 ft. maximum with 24 AWG wire; 1600 ft. maximum with 22 AWG wire.

 

 

3

Earth Ground Only.

 

 

4

Switch Input. A closure between terminals 4 and 6 will cause the designated relay(s) to activate for the

 

programmed strike time. The Postal Switch is connected here.

 

 

5

Microphone Input.

 

 

6

Common for switch input, microphone, speaker, AZ buttons, keyboard and battery negative.

 

 

7

Speaker Output.

 

 

8

Keyboard Data Input (not used).

 

 

9

Keyboard 5 VDC Power (not used).

 

 

10

Keyboard Clock Input (not used).

 

 

11

Z Button Input.

 

 

12

A Button Input.

 

 

13

Relay 2 Common – 30 Volt, 3 Amp maximum.

 

 

14

Relay 2 Contact (set for normally open or normally closed by the relay contact shorting bar on the circuit

 

board) – 30 Volt, 3 Amp maximum.

 

 

15

Relay 1 Common – 30 Volt, 3 Amp maximum.

 

 

16

Relay 1 Normally Closed – 30 Volt, 3 Amp maximum.

 

 

17

Relay 1 Normally Open – 30 Volt, 3 Amp maximum.

 

 

18

Back-up Battery POSITIVE (connect negative to terminal 6).

 

 

19

16 VAC Input Power – 20 VA minimum for 1803PC and 1815; 40 VA minimum for 1817.

 

100 ft. maximum with 18 AWG wire; 200 ft. maximum with 16 AWG wire.

 

 

20

16 VAC Input Power – 20 VA minimum for 1803PC and 1815, 40 VA minimum for 1817.

 

100 ft. maximum with 18 AWG wire; 200 ft. maximum with 16 AWG wire.

 

 

Do not run high voltage (115 V) power lines and communication lines in the same conduit. These should be in separate conduits at least six (6) inches apart. Be sure that all phone line wiring is twisted and completely isolated from ground.

Use only the supplied 16.5 VAC (or U.L. listed equivalent) to power the entry system. Do not power any other devices (electric strikes, magnetic locks, lights, etc.) from this transformer. Do not run 16 VAC entry system power lines over 200 feet. It is advisable to keep these wires as short as possible. Use 18 AWG wire for wire runs up to 100 feet, and 16 AWG wire for wire runs up to 200 feet. Install a low voltage surge suppresser (DoorKing p/n 1878-010 or equivalent) to help protect the entry system from power surges. Relay 1 contacts are located on the main terminal strip (15, 16, 17). Relay 2 contacts are located on the main terminal strip (13, 14) and are set for N.O or N.C. operation by the relay 2 shorting bar. Relay 0 contacts are located on an auxiliary terminal and are labeled on the board left to right: NO, NC, C.

A 12 volt .8 amp hour gel-cell battery (DoorKing p/n 1801-008) can be installed in the system to provide stand-by power in the event of a power outage. Connect the positive (RED) lead to terminal 18; connect the negative (BLACK) lead to terminal 6.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 1803PC, 1815, 1817 PC Programmable Telephone Entry Systems Page Use this manual with the following models only Table of Contents Adjustments Listing Important NoticeGeneral Information Features Installation Guidelines ALL Systems InstallationSurface Mount Units Surface Mount Units with Recess Box Flush Mount Units Flush Mount Rough-in Box Flush Mount Trim Ring Flush Mount Surface Mounting Kit Wall Mount Units Memory Chip Installation Postal Lock Installation Wiring 18AWG Terminal Description Main Terminal DescriptionWeigand Power Terminals Weigand Terminal DescriptionWeigand Data Terminals 4 RS-232 Terminals Elevator Control TerminalsControlling a Single Door or Gate Relay Wiring TypicalControlling a Gate Operator and Pedestrian Gate or Door Magnetic Lock Electric Strike Gate Operator Tracker Expansion Board Control Page Programming with a PC General Programming InformationProgramming from the Keypad System Memory Standard Chip MemPLUS ChipProgramming with a PC Master CodeSingle or Multiple Systems PC Programming Table Programming for Call-up OperationGeneral Programming Relay Strike TimeTalk Time Tone Open Numbers Postal SwitchRotary-dial Touch-tone / Rotary-dialProgramming Letters and Numbers Programming LETTERS, Numbers and MessagesProgramming the User Message 1815 Systems Programming the Instruction Message 1815 Systems Programming the User Message 1817 Systems Programming the Instruction Message 1817 Systems Programming Phone Numbers and Names Programming 7-digit Phone Numbers Programming the Directory Code LengthProgramming Phone Numbers with Area Code Reference Programming Area CodesProgramming Names 1815, 1817 Systems Only Deleting Individual Phone NumbersDelete Names 1815, 1817 Systems Only Display Phone Numbers 1815, 1817 Systems Only Delete Area CodesProgramming Device Codes Programming Device CodesDeleting Device Codes Programming Four-digit Entry Codes FOUR-DIGIT Entryt CodesDelete Four-digit Entry Codes Entry Code RangesFeedback Speaker VolumeClick Sensitivity Display Contrast 1815 OnlyBack-light Cutoff 1817 Only Master Code SwitchRing Pin Relay 2 Contact PinAdjustment Locations SEC Level Back Light Contrast Lower Contrast Upper Volume Guest Instructions Operating InstructionsUsing an Entry Code Resident InstructionsResponding to a Guest Call System Administrator Tracker Board Override Hold Open CommandOpening from a Remote Location Time and Date Check Relay CheckLine Sharing Miscellaneous Operating InstructionsConnection to a PBX Areas with 10-digit DialingPage Trouble Shooting MaintenanceSympton Possible Solutions 1 RS-232 Test Will be erased when this function is performedElevator Boards Hardware Test Weigand Test 1815, 1817 Systems OnlyElevator Board / Floor Hardware Test Accessories LOG Tables Name AAC Phone Number DIR Code ENT Device SEC FL ER Level Access Code Granting or Denying AccessGuest Communication Call Waiting

1815, 1803PC, 1817 specifications

DKS Enterprises has established itself as a leading provider of cutting-edge access control solutions, and among its notable offerings are the 1803PC, 1817, and 1815 models. These products stand out in the commercial security landscape, providing businesses with reliable and efficient entry management.

The DKS 1803PC is an advanced digital keyless entry system designed for commercial applications. Its primary feature is the easy-to-use keypad interface, which allows users to input their access codes directly. This model is equipped with a robust memory capable of storing up to 100 unique codes, making it suitable for locations with multiple users. Additionally, the 1803PC supports timed access, enabling businesses to set specific entry windows, which enhances security and access control.

The DKS 1817 model takes entry management a step further with its smart technology integration. It features Bluetooth capabilities that allow users to unlock doors via their smartphones, offering convenience and flexibility. The 1817 can be connected to various security devices, such as alarms and surveillance cameras, providing a comprehensive security ecosystem. It also includes a user-friendly mobile app that enables remote management of access permissions, ensuring that business owners can monitor and control entry points effectively from anywhere.

In contrast, the DKS 1815 model caters to businesses looking for a cost-effective yet reliable access solution. This model features a straightforward keypad interface similar to the 1803PC, but it is designed with essential functionalities to meet basic security needs. The 1815 supports up to 50 access codes and is ideal for smaller businesses or limited access areas. Its durable construction ensures longevity and requires minimal maintenance over time.

All three models employ DKS's proprietary technology that emphasizes durability and security. They are built to withstand harsh environmental conditions, making them suitable for both indoor and outdoor use. Each model adheres to stringent safety standards to protect against unauthorized access, ensuring the safety of personnel and assets.

In conclusion, DKS Enterprises' 1803PC, 1817, and 1815 models represent a diverse range of access control solutions tailored for various business needs. Their features focus on ease of use, advanced technology, and reliability, making them an excellent choice for organizations looking to enhance their security measures while streamlining access management.
Top Page Image Contents