ClearSounds v407 user manual Noise, Static, Interference while using the handset

Page 32

Call will not dial or dials very slowly

1.Check that the phone is in the correct dialing mode, Touch-Tone / Pulse Setting (See page #14).

No audible ringer

1.Make sure the ringer is not set to the “OFF” position (See figure #8).

2.Check the volume level of the ringer.

3.You may have too many extensions on your line. Try unplugging a few devices. Having too many telephones /accessories can also create problems such as low ringer volume or impaired quality during calls.

No Strobe Ringer and/or bed shaker will not activate

1.Make sure the strobe and/or shaker switch is turned “ON”(See figure #12).

2.Make sure the Bed Shaker is plugged in all the way.

3.Make sure the Bed Shaker is plugged into the correct jack (See figure #11).

No amplification

1.Check to see if the AMPLI amplify button is “ON” (See figure #24). The red light should be lit.

2.Check the AC Power Adapter and make sure it is plugged into the wall and into the appropriate jack on the phone.

Noise, Static, Interference while using the handset

1. A filter may be required for homes with DSL line or near Radio towers.

There is a red light that continues to flash

1.You have un-reviewed Caller ID / Call Waiting information or missed a call (See page #24).

2.Your Voice Mail account needs to be set-up as Visual Indicator only. Contact your local phone company; if the account is setup as Audible or Audible/Visual indicator, the light will contine to flash after reviewing your voice mail messages.

Difficulty storing numbers in memory

1.Make sure you are pressing the correct sequence of buttons for storing numbers.

2.If you are interrupted by the telephone company’s recorded announcement telling you to hang up or by a loud buzzing noise, ignore and continue to store the num- bers. Or hang up and store the number without lifting the handset or temporarily disconnect the telephone line until you have programmed in all the numbers.

No numbers dialed when memory button is pressed

1.No number stored in that memory button.

2.Make sure phone number was programmed and saved in the memory (See pages 16).

3.Make sure programming is done in the correct dial mode (touch-tone or pulse dial- ing).

4.If your phone has been disconnected for a few hours the numbers stored will be lost.

32

Image 32
Contents CSC50 Congratulations on your purchase Table Of Contents CSC50 Miscellaneous Feature Setting Troubleshooting GuideWarranty and Service SpecificationsComponents Figure #1Please Save These Instructions Features & Functions Figure #2Figure #3 Figure #4 Care of Phone LCD Screen & DisplayBattery Safety Installation StepsInstalling the Optional Batteries Wall Mount Use Phone Mounting InstallationsDesk / Table Use Setting the Dialing Mode Figure #7 Reversing The HookStrobe & Optional Bed Shaker Ring Signaling Ringer VolumeProgramming the Ringer & Auxiliary Alert Ring StyleFigure #14 Strobe Ringer Flashing incoming call indicator Programming Memory Dial ButtonsFigure #17 Making and Receiving a Call Using the SpeakerphoneCSC50 Phone Operation Using Audio and Telephone Headset Accessory Jacks Voice Amplification and Tone Using the Amplification FunctionReceiving/Answering a Call Figure #24 Amplify Button Using the Outgoing Speech Volume Using the volume reset overrideUsing your CSC50 Amplified Phone with hearing aids Using The Last Number Redial Using The Flash ButtonUsing The Mute Button CSC50 Caller ID OperationMessage Waiting Viewing Incoming CallsNew Calls / Message Waiting Indicator Light Review Call HistoryTurn on The Call Waiting Caller ID Feature Remove Call Record From The Caller ID ListCall Waiting Remove a Specific Call RecordDisplay Screen Messages CSC50 Miscellaneous Feature SettingsSet The Language Set Area Code / LDS Long Distance Service Code LCD / Screen Contrast AdjustmentDIM X------x Adjust Number of Digits Choosing The Date / Hour FormatDate format Hour formatTo Review / Modify a Number/Name In Your Phone Book Setting Up Your Phone BookTo Add a New Number/Name Recall / Delete One Of the Last 30 Numbers Dialed To Delete a Number From Your Phone BookTo Save Numbers From Caller ID To The Phone Book To Dial a Number From The Phone BookTroubleshooting Guide Auto on HookNoise, Static, Interference while using the handset FCC Registration Notice SpecificationsThis equipment is hearing aid compatible Page Page Téléphone amplifié Page Étapes d’installation Mode d’emploi du téléphone CSC50Table des matières Fonctionnement de l’identificateur de l’appelant du CSC50Garantie et service Réglage de diverses fonctions du CSC50Guide de dépannage Fiche techniqueComposants Veuillez Conserver CES Consignes Caractéristiques et fonctions Bouton supprimer Bouton haut Bouton bas OK bouton accepterCôté gauche Côté droit Arrière Dessous Combiné Entretien du téléphone Réglage DU Mode DE Numérotation Étapes d’installationInstallation DES Piles Facultatives Volume de la sonnerie Style de sonneriePrise facultative pour vibreur Touche de programmationn Utilisation murale Installations DE Montage DU TéléphoneUtilisation sur bureau / table Inversion du crochet Utilisation DU Téléphone À HAUT-PARLEUR Mode d’emploi du téléphone CSC50Acheminement ET Réception D’UN Appel Pour alterner entre le combiné et le haut-parleur Prise audio/collierPrise de casque téléphonique Acheminement d’un appelUtilisation de la fonction d’amplification Amplification de la voix et tonalitéBouton d’amplification supplémentaire du combiné Utilisation de la fonction Volume vocal sortant Commutateur d’annulation du rétablissement du volumeUtilisation de la touche Flash commutateur Utilisation de la touche Mute silenceVisualisation de l’écran d’affichage Total et nouveaux appelsVisualisation des appels entrants No Calls pas d’appelIndicateur de décharge des piles Message en attenteConsultation de l’historique des appels Indicateur de nouveaux messages / messages en attenteMessage en attente Retirer un enregistrement d’appel particulier’écran afficheDEL? supprimer? Retirer tous les enregistrementsRéglage DE Diverses Fonctions DU CSC50 Choix de la languePhone réglage du téléphone Waiting messages en attenteRéglage de l’indicatif régional / indicatif interurbain LDS Réglage du contraste de l’écran à cristaux liquides Choix du format de la date / heureDu téléphone Traste de l’écran à cristaux liquidesDIM Création de votre bottin téléphoniqueFormat de l’heure Pour ajouter un nouveau numéro ou un nouveau nomPour supprimer un numéro de votre bottin téléphonique Raccrochage Automatique Pour composer un numéro à partir du bottinGuide de dépannage Pas de tonalitéFiche technique Gain maximumDimensions Déclaration de conformité FCCGain maximum en sortie AlimentationPage Page Teléfono con amplificación de volumen Page Página Páginas Guía de identificación y resolución de problemas ÍndiceConfiguración de funciones diversas del teléfono CSC50 EspecificacionesComponentes Guarde Estas Instrucciones Características y funciones Botón OK aceptarCaracterísticas y funciones Características y funciones Cuidado del teléfono Selección DEL Modo DE Discado Procedimiento de instalaciónInstalación DE LAS Baterías Opcionales Ring configurar timbrado Volumen de timbradoEstilo de timbrado Programación DE LOS Botones DE Discado EN UN Solo Toque Toque Instalación en la pared Opciones DE Montaje DEL TeléfonoInstalación sobre superficie plana mesa/escritorio Figura18 Inversión del gancho USO DEL Altoparlante Funcionamiento del teléfono CSC50Ejecución Y Recepción DE Llamadas Recepción y contestación de llamada con el altoparlante Cómo alternar entre el auricular y el altoparlanteTerminal de conexión de audífonos telefónicos Ejecución de una llamadaRecepción y contestación de llamadas Amplificación del volumen y ajuste del tono de sonidoUso de la función de amplificación Del botón Ampli permanece encendida. Ampli Uso del bloqueo del restablecimiento del volumen Volumen de salidaRepetición del último número discado Uso del botón de transferencia FlashUso del botón silenciador Mute Funcionamiento DEL Idelntificador DE Llamadas DEL CSC50Visualización de llamadas entrantes No hay llamadasIndicador de batería baja Mensaje en esperaRevisión del historial de llamadas Luz indicadora de llamadas nuevas o mensajes en esperaLlamada en espera Borrado de un solo registro de llamadaBorrado de todos los registros de llamadas Activación del identificador de llamadas en esperaLanguage programar idioma Mensajes de la pantallaPhone configurar teléfono Configuración del código de área y el código de país Regulación del contraste de la pantalla de cristal líquidoArea & LDS configurar código de área y de país Contrast contraste de pantallaSelección del formato de presentación de la fecha y la hora Formato de presentación de fechaFormato de presentación de la hora Format formato de fechaRevisión o modificación de nombre o número en el directorio Configuración del directorio telefónicoPara agregar un nuevo número con nombre Para borrar un número del directorio Para discar un número desde el directorioRestablecimiento Automático DE LA Línea Con los botones de flecha, elija on activar u OFF desactivarGuía de identificación y resolución de problemas Requisitos de energía Amplificación de salida máxima +12 dB DimensionesEspecificaciones Amplificación máxima Aviso de registro del aparato ante la FCC Autoridad federal de comunicaciones de los EE.UUEste aparato es compatible con prótesis auditivas