Panasonic KX-TG2340JX If the Following Appear on Your Display, Display message Cause & Remedy

Page 54

PQQX14670ZA.book 54 ページ 2005年2月22日 火曜日 午後12時0分

If the Following Appear on Your Display...

The following will be displayed when the unit needs your attention.

Display message

Cause & Remedy

 

 

Recharge battery

• The battery needs to be charged. Recharge the

 

battery (p. 9).

 

 

Charge for 6h

• The battery has been discharged. The handset will

 

not work. Fully charge the battery (p. 9).

 

 

No link to base.

• The handset has lost communication with the base

Move closer to

unit. Walk closer to the base unit and try again or

base, try again.

re-register the handset (p. 49).

 

• Confirm the base unit’s AC adaptor is plugged in.

 

• Raise the base unit antenna.

 

 

Please lift up

• A handset button was pressed while the handset

and try again.

was on the base unit. Lift the handset and press the

 

button again.

 

 

Busy

• The base unit is in use. Try again later.

Error!!

• When you tried to re-register the handset, the

 

handset and base unit could not link for some

 

reason, such as interference from electrical

 

appliances. Move the handset and base unit away

 

from any electrical appliances and try again.

 

 

Phone book full

• When you tried to store an item in the phone book,

 

the phone book memory was full. Press [OFF] to exit

 

the programming mode. To erase other items from

 

the phone book, see page 37.

 

 

System is busy.

• The handset has lost communication with the base

Please try again

unit. Walk closer to the base unit and try again.

later.

 

Save error

• The entered password was wrong in programming

 

the Dial Lock. Enter the correct password.

 

 

Dial locked

• The Dial Lock is turned on. If necessary, cancel the

 

Dial Lock (p. 48).

 

 

Line in use

• The base unit is conducting an outside call or a

 

parallel connected telephone is in use.

 

 

Line on hold

• The base unit is on hold for an outside call.

54

Image 54
Contents Charge the battery for 6 hours before initial use Digital Cordless PhonePulse-or-tone dialing capability Accessories included For your future referenceBattery Charge For Best PerformanceBase Unit Location/Noise Contents Contents Location of Controls Base unitHandset soft keys Location of ControlsHandset Handset navigator keyInstallation ConnectionsTo replace the battery Installation Installing the Battery in the HandsetBattery strength Display prompt Battery strengthBattery replacement InstallationBattery information RechargeProgrammable Settings How to select a function item from the menuProgramming Guidelines Handset Programmable Settings Function Menu Table Handset Main menuProgrammable Settings Date and Time Handset To confirm the date and time, repeat steps 1 and 2 aboveProgrammable Settings Dialing Mode Handset Line Mode HandsetSelect On or Off by pressing d or B Programmable Settings Auto Talk HandsetScroll to Auto talk by pressing d or B Auto talk Off KBack d B Save LSelect the desired volume level by pressing d or B Programmable Settings Ringer VolumeHandset ringer volume Handset Ringer volume Low High KBack dB SaveLTo turn the ringer on, press Volume or Programmable SettingsBase unit ringer volume Base Unit Make sure the base unit is not being usedScroll to Ringer tone by pressing d or Programmable Settings Ringer ToneHandset ringer tone Handset Select the desired ringer tone by pressing dSetting the base unit ringer tone by using the Handset LCD Contrast HandsetTo have a hands-free phone conversation Using the Handset HandsetMaking Calls Hands-free Digital Duplex SpeakerphoneMaking Calls To adjust the receiver/speaker volume during a conversationTo redial using the redial list Memory Redial To dial after confirming the entered numberTo put a call on hold Voice Enhancer TechnologyBacklit LCD display/Lighted handset keypad Press SP-PHONE Making Calls Using the Base Unit Base UnitTo adjust the speaker volume during a conversation To return to the call, press SP-PHONETalk into the MIC To hang up, press SP-PHONE Answering CallsBase Unit OFF s Auto TalkPrivate name display Caller ID ServiceHow Caller ID information is displayed Display MeaningCaller ID Service Using Talking Caller ID Announcing caller information Talking Caller IDBase unit Talking Caller ID feature Handset Caller ID ServiceHandset Talking Caller ID feature Handset To turn Talking Caller ID on or offPress Rcvd calls, , or To enter Using the Caller ListViewing the Caller List Caller ListWhat , means Using the Caller ListCalling Back from the Caller List Handset If a caller calls more than oncePress Rcvd calls, d, or B to enter the Caller List Scroll to the desired caller by pressing d orPress Select Press Edit Press Rcvd calls, d, or B to enter Press SelectUsing the Caller List Erasing Caller Information Handset To erase a specific callerTo erase all entries Phone Book Storing Names and Numbers HandsetTo store an emergency number Selecting characters to enter names If you make a mistake when entering a name or numberPhone Book For example, to enter TomTo search for a name by initial Phone Book Dialing from the Phone Book HandsetPress Search Press d repeatedly until the desired name is displayedWhile you are on a call Press Menu Chain Dial HandsetIndex table Search for the desired item by pressing d orPhone Book Editing an Item in the Phone Book Handset Erasing an Item in the Phone Book HandsetFrom Handset IntercomMaking Intercom Calls From Base UnitPress SP-PHONE or LOCATOR/INTERCOM Intercom Answering Intercom CallsPress C, s or HOLD/INTERCOM Call from BaseFrom the Base Unit to the Handset Transferring a CallFrom the Handset to the Base Unit Press SP-PHONE or LOCATOR/INTERCOM to answerTransferring a Call Quick call transferConference Calls To join a conversation Call ShareDuring a call, press LOCATOR/INTERCOM Temporary Tone Dialing Special FeaturesFor Call Waiting Service Users Muting Your ConversationFlash Button Handset Base Unit Special Features Using the Pause KeyFor PBX Line/Long Distance Calls Handset Selecting the flash time HandsetBase unit incoming call tone Handset Special Features Incoming Call Tone Handset Base UnitHandset incoming call tone Handset Scroll to Incoming call. by pressing dSelect Off or On by pressing d or B Special Features Key Tone HandsetScroll to Key tone by pressing d or B Key tone KBack d B Save LSpecial Features Dial Lock Handset Base UnitPress Dial Lock Was turned on Enter the password set when the Dial LockEnter the password set when the Dial Lock was turned on @@@@Press and hold LOCATOR/INTERCOM until a beep sounds Handset 1 RegisteredTo attach the belt clip To remove the belt clip Belt ClipShoulder Rest Attachment To attach the shoulder rest attachmentWall Mounting Wall TemplateConnecting the optional headset To switch to the speakerphone while using the headsetOptional Headset Direct Commands Menu item Command Selection itemsDuring programming If the Following Appear on Your Display Display message Cause & RemedyTroubleshooting Troubleshooting Problem Cause & RemedyRecharge battery is But Recharge battery isSafety Instructions Specifications Safety Instructions62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan PQQX14670ZA F0205-0D