Troubleshooting

Panasonic KX-TG2340JX operating instructions Troubleshooting

Page 55

PQQX14670ZA.book 55 ページ２００５年２月２２日火曜日午後１２時０分

If the handset display shows error messages, see “If the Following Appear on Your Display...” (p. 54) for the Cause & Remedy.

Problem

Cause & Remedy

“No link to base. Move closer to base, try again.” is displayed and an alarm tone sounds.

•You are too far from the base unit. Walk closer to the base unit.

•Confirm the base unit’s AC adaptor is plugged in.

•Raise the base unit antenna.

•If the above remedies do not solve the problem, the handset may have lost communication with the base unit. Register the handset again (p. 49).

The handset and/or base unit	• Check the settings (p. 8–10).
does not work.	• Check whether the dialing mode setting is
	correct (p. 14).
	• Fully charge the battery (p. 9).
	• Clean the charge contacts and charge again
	(p. 10).
	• Check battery Installation (p. 9).
	• Unplug the base unit’s AC adaptor to reset it.
	Plug in, and try again.
	• Re-install the battery (p. 9) and fully charge it.

Static, sound cuts in/out, fades. Interference from other electrical units.

•Move the handset and base unit away from other electrical appliances (p. 3).

•Walk closer to the base unit.

•Raise the base unit antenna.

•If the unit is connected to a telephone line with DSL service, you may hear noise from the receiver or speaker during conversations. We recommend connecting a noise filter (contact your DSL service provider) to the telephone line between the unit and the telephone line jack.

The handset and/or base unit	• The ringer volume is turned off. Set to high,
does not ring.		medium, or low (p. 16, 17).
The handset display is blank.	• If the handset display is blank, fully charge
		the battery (p. 9).
You cannot program any	• Programming is not possible while the
function items.		handset and/or base unit is being used.
	• Do not pause for over 60 seconds while
		programming.
	• Walk closer to the base unit.
	• When the Dial Lock is turned on (p. 47), you
		cannot store the phone number in the phone
		book.

Useful Information

Image 55

Contents

Digital Cordless Phone Charge the battery for 6 hours before initial usePulse-or-tone dialing capability For your future reference Accessories includedFor Best Performance Battery ChargeBase Unit Location/Noise Contents Contents Base unit Location of ControlsHandset navigator key Location of ControlsHandset Handset soft keysConnections InstallationDisplay prompt Battery strength Installation Installing the Battery in the HandsetBattery strength To replace the batteryRecharge InstallationBattery information Battery replacementHow to select a function item from the menu Programmable SettingsProgramming Guidelines Handset Main menu Programmable Settings Function Menu Table HandsetTo confirm the date and time, repeat steps 1 and 2 above Programmable Settings Date and Time HandsetLine Mode Handset Programmable Settings Dialing Mode HandsetAuto talk Off KBack d B Save L Programmable Settings Auto Talk HandsetScroll to Auto talk by pressing d or B Select On or Off by pressing d or BRinger volume Low High KBack dB SaveL Programmable Settings Ringer VolumeHandset ringer volume Handset Select the desired volume level by pressing d or BMake sure the base unit is not being used Programmable SettingsBase unit ringer volume Base Unit To turn the ringer on, press Volume orSelect the desired ringer tone by pressing d Programmable Settings Ringer ToneHandset ringer tone Handset Scroll to Ringer tone by pressing d orLCD Contrast Handset Setting the base unit ringer tone by using the HandsetHands-free Digital Duplex Speakerphone Using the Handset HandsetMaking Calls To have a hands-free phone conversationTo dial after confirming the entered number To adjust the receiver/speaker volume during a conversationTo redial using the redial list Memory Redial Making CallsVoice Enhancer Technology To put a call on holdBacklit LCD display/Lighted handset keypad To return to the call, press SP-PHONE Making Calls Using the Base Unit Base UnitTo adjust the speaker volume during a conversation Press SP-PHONEOFF s Auto Talk Answering CallsBase Unit Talk into the MIC To hang up, press SP-PHONEDisplay Meaning Caller ID ServiceHow Caller ID information is displayed Private name displayAnnouncing caller information Talking Caller ID Caller ID Service Using Talking Caller IDTo turn Talking Caller ID on or off Caller ID ServiceHandset Talking Caller ID feature Handset Base unit Talking Caller ID feature HandsetCaller List Using the Caller ListViewing the Caller List Press Rcvd calls, , or To enterIf a caller calls more than once Using the Caller ListCalling Back from the Caller List Handset What , meansScroll to the desired caller by pressing d or Press Rcvd calls, d, or B to enter the Caller ListPress Select Press Edit Press Select Press Rcvd calls, d, or B to enterTo erase a specific caller Using the Caller List Erasing Caller Information HandsetTo erase all entries Storing Names and Numbers Handset Phone BookTo store an emergency number For example, to enter Tom If you make a mistake when entering a name or numberPhone Book Selecting characters to enter namesPress d repeatedly until the desired name is displayed Phone Book Dialing from the Phone Book HandsetPress Search To search for a name by initialSearch for the desired item by pressing d or Chain Dial HandsetIndex table While you are on a call Press MenuErasing an Item in the Phone Book Handset Phone Book Editing an Item in the Phone Book HandsetFrom Base Unit IntercomMaking Intercom Calls From HandsetCall from Base Intercom Answering Intercom CallsPress C, s or HOLD/INTERCOM Press SP-PHONE or LOCATOR/INTERCOMPress SP-PHONE or LOCATOR/INTERCOM to answer Transferring a CallFrom the Handset to the Base Unit From the Base Unit to the HandsetQuick call transfer Transferring a CallTo join a conversation Call Share Conference CallsDuring a call, press LOCATOR/INTERCOM Muting Your Conversation Special FeaturesFor Call Waiting Service Users Temporary Tone DialingSelecting the flash time Handset Special Features Using the Pause KeyFor PBX Line/Long Distance Calls Handset Flash Button Handset Base UnitScroll to Incoming call. by pressing d Special Features Incoming Call Tone Handset Base UnitHandset incoming call tone Handset Base unit incoming call tone HandsetKey tone KBack d B Save L Special Features Key Tone HandsetScroll to Key tone by pressing d or B Select Off or On by pressing d or BDial Lock Handset Base Unit Special FeaturesPress Dial Lock @@@@ Enter the password set when the Dial LockEnter the password set when the Dial Lock was turned on Was turned onHandset 1 Registered Press and hold LOCATOR/INTERCOM until a beep soundsTo attach the shoulder rest attachment Belt ClipShoulder Rest Attachment To attach the belt clip To remove the belt clipWall Template Wall MountingTo switch to the speakerphone while using the headset Connecting the optional headsetOptional Headset Menu item Command Selection items Direct CommandsDuring programming Display message Cause & Remedy If the Following Appear on Your DisplayTroubleshooting Problem Cause & Remedy TroubleshootingBut Recharge battery is Recharge battery isSafety Instructions Safety Instructions SpecificationsPQQX14670ZA F0205-0D 62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan

Related manuals

Panasonic KX-TG2340JX operating instructions Troubleshooting

Troubleshooting