Uniden UH-057 manual Select the lead-In Tone you want to use Example, To remove the lead-In Tone

Page 35

To program:

1.Press the @l) Key for about 1.5 sec.

Two beeps will be heard and the lCD displays:

[ - -]

2.Press the @ Key. The PRI indicator appears on the lCD display and flashing.

, I I"

-

8:» ..

 

PAl

 

 

...I I ..

 

 

3. Select the lead-In Tone you want to use.

 

Example:

 

 

 

Selecting the Tone assigned to digit 1.

 

Press (D. The lCD displays:

-

 

 

 

, I I"

 

-I

 

PAI-

 

I

..

 

3. Pressthe@l) Key to complete the programming. Two beeps will be heard and the lCD returns to its previous status prior to accessing Programming Mode.

To remove the lead-In Tone:

1.Follow steps 1 and 2 of lead-In Tone Programming.

2.Press and hold @l) Key for about 1.5 sec until you hear the two beeps. the lCD will display "E" Tone but it will not be programmed to the memory.

Be careful not to press the @l) key twice.

Otherwise, "E" tone will be programmed as your lead-In Tone.

Note: Make sure that all members of your group will use the same Lead-In Tone. Else, you will lessen the probability of receiving and successfully decoding a se/call call while TSQ Scanning.

Page 33

UH-O57

Page 34 Page 36
Image 35
Page 34 Page 36
Contents
UnidenSUNDOWN ERUH-57 Uniden~ is a registered trademark of Uniden Corporation Nickel-Cadmium Battery WarningTable of Contents Selcall 3UH-O57 Descrl ptlonUlrements Feature Highlights UH-O5J UH-O57 Belt Clip Wrist strapLocks out a selected channel from channel scan Top Indicators and Display~~88 AC Adaptor/Charger Jack Connect AC Adaptor/Charger here Side Controls and ConnectorsTX Power HI/LOW Switch -Press to set the Transmit Built-in Speaker Audio Output Front ControlsRX ID, TX ID, or lead-In tone Enter lead-In Delay ProgrammingUH-O57 Hash Key Press and hold for 1.5 sec toChannel Enter Key Press to enter the selectedGetting Started Antenna Battery InformationBelt Clip Installation Recharging the Nickel-Cadmium Battery PackOperation To resume scanning, press the 0 Key Channel ScanPress D PriorityScanning is inactive in TSO Scan ModeCreate a Channel Scan List with Channel Lock-Out Feature Transmit Maximum transmit power output level of UH-O57is 5 wattsDisplay Low Battery Level DetectionButton. DUP indicator appears on the LCD Display Special Feature Example Choosing CH20 as your Call Channel Puts the receiver on Quiet Mode also known as ToneRequired Selcallid to open the Quiet condition is received Tone Squelch Scanning When a call is receivedKey Cancel TSQ Scanning by pressing either the 0 orUsing the 0 or 0 Key, browse through the TSQ Channels When a Selcall is received, press the PIT SwitchRadios Tone CallingTX Selcall ID Format 3 4 D Receiver Selcall ID CD 1ADJ Press the @ Key Transmitter Selcall IDTcAL ProgrammingMSec Other SELCALLParametersLead-In Delay Sec Lead-In ToneKey LCD Display To remove the lead-In Tone Select the lead-In Tone you want to use ExampleProgramming Guide Delay SPage35UH-O57 Care and MaintenancePrincess Highway, Rockdale, NSW ServiceUHF CB Channel Information Duplex Operating Mode Simplex Operating ModeButtons ChannelsTransm itter Warranty UTZZO1857ZZ
Related manuals
Manual 44 pages 29.17 Kb