Uniden UH-057 manual UHF CB Channel Information

Page 39

UHF CB CHANNEL INFORMATION

SIMPLEX Operating Mode

Channel	Transmit	Receive
Assignment	Frequency(MHz)	Frequency(MHz)
1	476.425	476.425
2	476.450	476.450
3	476.475	476.475
4	476.500	476.500
5	476.525	476.525
6	476.550	476.550
7	476.575	476.575
8	476.600	476.600
9	476.625	476.625
10	476.650	476.650
11	476.675	476.675
12	476.700	476.700
13	476.725	476.725
14	476.750	476.750
15	476.775	476.775
16	476.800	476.800
17	476.825	476.825
18	476.850	476.850
19	476.875	476.875
20	476.900	476.900
21	476.925	476.925
22	476.950	476.950
23	476.975	476.975
24	477.000	477.000
1
L	477.025	477.025
25	477.025	477.025
26	477.050	477.050
27	477.075	477.075
28	477.100	477.100
29	-477.125	477.125
30	477.150	477.150
31	477.175	477.175
32	477.200	477.200
33	477.255	477.255
	Page 37	UH-O57

'-

Image 39

Contents

UnidenSUNDOWN ERUH-57 Uniden~ is a registered trademark of Uniden Corporation Nickel-Cadmium Battery WarningTable of Contents Selcall Descrl ptlon Ulrements3UH-O57 Feature Highlights UH-O5J UH-O57 Belt Clip Wrist strapLocks out a selected channel from channel scan Top Indicators and Display~~88 Side Controls and Connectors TX Power HI/LOW Switch -Press to set the TransmitAC Adaptor/Charger Jack Connect AC Adaptor/Charger here Built-in Speaker Audio Output Front ControlsRX ID, TX ID, or lead-In tone Enter lead-In Delay ProgrammingUH-O57 Hash Key Press and hold for 1.5 sec toChannel Enter Key Press to enter the selectedGetting Started Antenna Battery InformationBelt Clip Installation Recharging the Nickel-Cadmium Battery PackOperation To resume scanning, press the 0 Key Channel ScanPress D PriorityScanning is inactive in TSO Scan ModeCreate a Channel Scan List with Channel Lock-Out Feature Transmit Maximum transmit power output level of UH-O57is 5 wattsLow Battery Level Detection Button. DUP indicator appears on the LCD DisplayDisplay Special Feature Puts the receiver on Quiet Mode also known as Tone Required Selcallid to open the Quiet condition is receivedExample Choosing CH20 as your Call Channel Tone Squelch Scanning When a call is receivedKey Cancel TSQ Scanning by pressing either the 0 orUsing the 0 or 0 Key, browse through the TSQ Channels When a Selcall is received, press the PIT SwitchTone Calling TX Selcall ID FormatRadios 3 4 D CD 1 ADJReceiver Selcall ID Press the @ Key Transmitter Selcall IDTcAL ProgrammingMSec Other SELCALLParametersLead-In Delay Lead-In Tone Key LCD DisplaySec To remove the lead-In Tone Select the lead-In Tone you want to use ExampleProgramming Guide Delay SPage35UH-O57 Care and MaintenancePrincess Highway, Rockdale, NSW ServiceUHF CB Channel Information Duplex Operating Mode Simplex Operating ModeButtons ChannelsTransm itter Warranty UTZZO1857ZZ

Related manuals

Manual 44 pages 29.17 Kb