Cobra Electronics MR HH415LI VP EU owner manual Backlight/Key Lock Button, MEM/ESC Button L Button

Page 37

Operating Your Radio

Backlight/Key Lock Button

Key Locked Buttons

PRESET

Key Lock Icon

Getting Started

Backlight/Key Lock Button

The LCD will be illuminated by the backlight as long as any button is pressed and will remain On for 10 seconds after the button is released.

To Display the Backlight Momentarily:

Press the Backlight/Key Lock button. The backlight will remain On for 10 seconds. If the backlight is already On, another press of the Backlight/Key Lock button will turn it Off.

Key Lock

To prevent accidental changes to your settings, you can lock all of the following buttons:

■Channel Up Button

■Channel Down Button

■SCAN Button

■MEM/ESC Button

■H-M-L Button

■16 Button

■TRI-WATCH Button

■Call/Enter/Setup Button

■Preset Button

■REW Button

To Lock or Unlock the Buttons:

Press and hold the Backlight/Key Lock button for two (2) seconds. The Key Lock icon will appear or disappear in the LCD. When Key Lock is On, pressing any of the listed buttons on the front of the radio will result in a three (3) beep error message.

Both the Backlight/Key Lock button and the Talk button are active — you can Receive (Rx) or Transmit (Tx) a message with Key Lock On, but you cannot change the channel.

32 English

Image 37

Contents MR HH415LI VP EU Our Thanks to You and Customer Assistance LCD Radio Controls and IndicatorsBacklit LCD Screen and Product Features Speaker/Mic Jack Product FeaturesTable of Contents Important Safety Information Important Safety InformationGeneral Precautions Important Safety Information Recommendations for Marine Communication Recommendations for Marine CommunicationStation License Licensing InformationCanadian or U.S.A. Station License Radio Call SignVHF Marine Radio Procedures Voice Calling Voice CallingVessel Corsair calling the vessel Vagabond Radiotelephone Calls Radiotelephone CallsEmergency Messages and Distress Procedure Emergency Messages and Distress ProcedureIf You Hear a Distress Call Marine Emergency SignalsTell where you are Marine Distress ProcedureSay End message by sayingFor Example VHF Marine Channel Assignments Port Operations Public Correspondence marine operatorNavigational Digital Selective CallingUSA 03A Government Only International Distress, Safety and Calling156.900 23A Government Only 21A U.S. Government Only Canada Coastguard Only61A U.S. Government Only Canada Coastguard Only Channel Digital Selective Calling Voice communications not allowed 64A U.S. Government Only Canada Commercial FishingLimits 81A U.S. Government Only Environmental Protection Operations Included in this Package Included in this PackageAntenna, Wrist Strap and Belt Clip Antenna InstallationWrist Strap Belt ClipBatteries and Charger Installing the Battery PackBatteries and Charger Initial Charge Alkaline Batteries To Remove Battery Pack from RadioMaintaining the Battery Charge Volume Control Power/Volume/Squelch Controls Power On/Off ControlGetting Started Common Radio FunctionsTalk Button Squelch ControlBacklight/Key Lock Button TRI-WATCH Button Call/Enter/Setup Button Preset ButtonTo Display the Backlight Momentarily Key LockScan Button To Toggle Between H-M-L Power Modes High/Medium/Low H-M-L Power ButtonCall /Enter/Setup Button To Set Personal Default Settings Setup Mode Programming Setup Mode ProgrammingInternational/Canada/USA Channel Maps To Set Channel Map Operating AreaTo set VibrAlert VibrAlert ModeTo Set Call Tone Call Tone ModeKey Tone Mode Roger Beep ModeTo Set Roger Beep On or Off To Set Key Tone On or OffAtis ID Programming Atis ID ProgrammingTo Set the Atis ID Number Atis ID Programming Standby/Receive and Transmit Marine Standby and Receive Rx ModeStandby/Receive Transmit Transmit Tx ModeTo Transmit a Message To Switch to Channel Channel 16 ModeAdvanced Operation Advanced OperationTri-Watch Setup To Program or Edit the Tri-Watch Channels Tri-Watch ModeTri-Watchmemory channels Using Tri-Watch Tri-Watch Scan ModeTo Program Memory Locations Memory Location ModeTo Recall a Stored Memory Location To Exit Memory Location ModeTo Erase Stored Memory Locations To Enter Channel Scan Channel Scan ModeMemory Location Scan Mode From Marine Standby mode, press the MEM/ESC button To Enter Memory Location ScanUsing Rewind-Say-Again Rewind-Say-Again FeatureExample Using Rewind-Say-Again to Record Audio Transmission Troubleshooting MaintenancePress Backlight Key Lock buttonSpecifications SpecificationsEnglish Accessories AccessoriesLapel Speaker/Microphone Declaration of Conformity and CE Marking