Cobra Electronics MR HH415LI VP EU owner manual Memory Location Mode, To Program Memory Locations

Page 52

Operating Your Radio

MEM/ESC Button

Memory Location Number

Channel Up/Down Button

Channel Number

Advanced Operation

Memory Location Mode

Your radio has unlimited memory locations for storing your most frequently used channels. These memory locations can be selected individually or can be scanned. (See page 50 under Memory Location Scan.)

To enter Memory mode, press MEM/ESC button. The display will show the MEM icon and the Memory Channel bank will be activated and displayed.

To Program Memory Locations:

1.Press and hold the MEM/ESC button for two (2) seconds. The memory location number will start flashing and the MEM icon will be turned On.

2.Use the Channel Up/Down button to advance to the memory location (00-99) you want to program.

3.Press the MEM/ESC button to select the memory location. The memory channel number will stop flashing and the channel number will start flashing.

4.Use the Channel Up/Down button to change to the channel you want to store into the selected memory location.

5.Press the MEM/ESC button to program that channel. The memory location number will flash again.

Repeat steps 2 through 5 to program as many additional memories as you want.

6.Press and hold the MEM/ESC button for two (2) seconds. This will return the radio to Memory mode.

7.Press and release the MEM/ESC button again to return to Marine Standby mode.

Nothing Comes Close to a Cobra® 47

Image 52

Contents MR HH415LI VP EU Our Thanks to You and Customer Assistance Radio Controls and Indicators LCDBacklit LCD Screen and Product Features Product Features Speaker/Mic JackTable of Contents Important Safety Information Important Safety InformationGeneral Precautions Important Safety Information Recommendations for Marine Communication Recommendations for Marine CommunicationLicensing Information Station LicenseCanadian or U.S.A. Station License Radio Call SignVHF Marine Radio Procedures Voice Calling Voice CallingVessel Corsair calling the vessel Vagabond Radiotelephone Calls Radiotelephone CallsEmergency Messages and Distress Procedure Emergency Messages and Distress ProcedureMarine Emergency Signals If You Hear a Distress CallMarine Distress Procedure Tell where you areSay End message by sayingFor Example VHF Marine Channel Assignments Public Correspondence marine operator Port OperationsNavigational Digital Selective CallingUSA International Distress, Safety and Calling 03A Government Only156.900 23A Government Only 21A U.S. Government Only Canada Coastguard Only61A U.S. Government Only Canada Coastguard Only Channel 64A U.S. Government Only Canada Commercial Fishing Digital Selective Calling Voice communications not allowedLimits 81A U.S. Government Only Environmental Protection Operations Included in this Package Included in this PackageAntenna Installation Antenna, Wrist Strap and Belt ClipWrist Strap Belt ClipBatteries and Charger Installing the Battery PackBatteries and Charger Initial Charge To Remove Battery Pack from Radio Alkaline BatteriesMaintaining the Battery Charge Power/Volume/Squelch Controls Power On/Off Control Volume ControlGetting Started Common Radio FunctionsSquelch Control Talk ButtonTRI-WATCH Button Call/Enter/Setup Button Preset Button Backlight/Key Lock ButtonTo Display the Backlight Momentarily Key LockScan Button To Toggle Between H-M-L Power Modes High/Medium/Low H-M-L Power ButtonCall /Enter/Setup Button To Set Personal Default Settings Setup Mode Programming Setup Mode ProgrammingInternational/Canada/USA Channel Maps To Set Channel Map Operating AreaVibrAlert Mode To set VibrAlertCall Tone Mode To Set Call ToneRoger Beep Mode Key Tone ModeTo Set Roger Beep On or Off To Set Key Tone On or OffAtis ID Programming Atis ID ProgrammingTo Set the Atis ID Number Atis ID Programming Marine Standby and Receive Rx Mode Standby/Receive and TransmitStandby/Receive Transmit Transmit Tx ModeTo Transmit a Message Channel 16 Mode To Switch to ChannelAdvanced Operation Advanced OperationTri-Watch Mode Tri-Watch Setup To Program or Edit the Tri-Watch ChannelsUsing Tri-Watch Tri-Watch Scan Mode Tri-Watchmemory channelsMemory Location Mode To Program Memory LocationsTo Recall a Stored Memory Location To Exit Memory Location ModeTo Erase Stored Memory Locations Channel Scan Mode To Enter Channel ScanMemory Location Scan Mode To Enter Memory Location Scan From Marine Standby mode, press the MEM/ESC buttonUsing Rewind-Say-Again Rewind-Say-Again FeatureExample Using Rewind-Say-Again to Record Audio Transmission Maintenance TroubleshootingPress Backlight Key Lock buttonSpecifications SpecificationsEnglish Accessories AccessoriesLapel Speaker/Microphone Declaration of Conformity and CE Marking