Cobra Electronics MR HH415LI VP EU Setup Mode Programming, International/Canada/USA Channel Maps

Page 41

Operating Your Radio

Setup Mode Programming

Setup Mode Programming

•

The following series of procedures is designed to allow you to set the programmable features of your radio. Correctly following these steps results in a minimal amount of radio setup programming time.

NOTE

When in the Setup mode, if you stop programming for longer than 15 seconds, your entry will be saved and the radio will go back to the Marine Standby mode. When you return to Setup mode and continue programming, you will see the last “value” displayed. While in the Setup mode, you will not receive any signal reception.

Marine (VHF) Mode Programming

Programming these features will allow you to customize certain features of this radio to enhance your “On-Water” audio needs.

Start from Marine Standby mode to begin Marine (VHF) Setup programming. Press and hold the Call/Enter/Setup button for two (2) seconds to enter the programming mode.

Set Channel Map

International/Canada/USA Channel Maps

Active Channel Map Icon

Channel Up/Down Button

Three (3) sets of VHF Channel Maps have been established for marine use in the USA, Canada, and the rest of the world (International). Most of the channels are the same for all three (3) maps, but there are definite differences (see table on pages 16 through 23). Your radio has all three (3) maps built into it and will operate correctly in whichever area you choose.

To Set Channel Map Operating Area:

1.The Channel Map mode is the first mode that begins the Marine (VHF) Setup programming.

2.U, I and C will display, with the current setting (the I icon is the default) flashing.

3.Press Channel Up/Down button to select the I, C or U icon.

4.Press Call/Enter/Setup button to save this entry and move to the next setup programming mode.

NOTE

One (1) or two(2) of the channel maps might have been disabled for sales of this radio in some countries.

36 English

Image 41

Contents MR HH415LI VP EU Our Thanks to You and Customer Assistance LCD Radio Controls and IndicatorsBacklit LCD Screen and Product Features Speaker/Mic Jack Product FeaturesTable of Contents Important Safety Information Important Safety InformationGeneral Precautions Important Safety Information Recommendations for Marine Communication Recommendations for Marine CommunicationStation License Licensing InformationCanadian or U.S.A. Station License Radio Call SignVHF Marine Radio Procedures Vessel Corsair calling the vessel Vagabond Voice CallingVoice Calling Radiotelephone Calls Radiotelephone CallsEmergency Messages and Distress Procedure Emergency Messages and Distress ProcedureIf You Hear a Distress Call Marine Emergency SignalsTell where you are Marine Distress ProcedureSay End message by sayingFor Example VHF Marine Channel Assignments Port Operations Public Correspondence marine operatorNavigational Digital Selective CallingUSA 03A Government Only International Distress, Safety and Calling156.900 61A U.S. Government Only Canada Coastguard Only 21A U.S. Government Only Canada Coastguard Only23A Government Only Channel Digital Selective Calling Voice communications not allowed 64A U.S. Government Only Canada Commercial FishingLimits 81A U.S. Government Only Environmental Protection Operations Included in this Package Included in this PackageAntenna, Wrist Strap and Belt Clip Antenna InstallationWrist Strap Belt ClipBatteries and Charger Installing the Battery PackBatteries and Charger Initial Charge Alkaline Batteries To Remove Battery Pack from RadioMaintaining the Battery Charge Volume Control Power/Volume/Squelch Controls Power On/Off ControlGetting Started Common Radio FunctionsTalk Button Squelch ControlBacklight/Key Lock Button TRI-WATCH Button Call/Enter/Setup Button Preset ButtonTo Display the Backlight Momentarily Key LockScan Button Call /Enter/Setup Button High/Medium/Low H-M-L Power ButtonTo Toggle Between H-M-L Power Modes To Set Personal Default Settings Setup Mode Programming Setup Mode ProgrammingInternational/Canada/USA Channel Maps To Set Channel Map Operating AreaTo set VibrAlert VibrAlert ModeTo Set Call Tone Call Tone ModeKey Tone Mode Roger Beep ModeTo Set Roger Beep On or Off To Set Key Tone On or OffTo Set the Atis ID Number Atis ID ProgrammingAtis ID Programming Atis ID Programming Standby/Receive and Transmit Marine Standby and Receive Rx ModeTo Transmit a Message Transmit Tx ModeStandby/Receive Transmit To Switch to Channel Channel 16 ModeAdvanced Operation Advanced OperationTri-Watch Setup To Program or Edit the Tri-Watch Channels Tri-Watch ModeTri-Watchmemory channels Using Tri-Watch Tri-Watch Scan ModeTo Program Memory Locations Memory Location ModeTo Erase Stored Memory Locations To Exit Memory Location ModeTo Recall a Stored Memory Location To Enter Channel Scan Channel Scan ModeMemory Location Scan Mode From Marine Standby mode, press the MEM/ESC button To Enter Memory Location ScanExample Rewind-Say-Again FeatureUsing Rewind-Say-Again Using Rewind-Say-Again to Record Audio Transmission Troubleshooting MaintenancePress Backlight Key Lock buttonSpecifications SpecificationsEnglish Lapel Speaker/Microphone AccessoriesAccessories Declaration of Conformity and CE Marking