Cobra Electronics MR HH415LI VP EU Using Rewind-Say-Again to Record Audio Transmission

Page 58

Operating Your Radio

SCAN Button Enter Record

Rewind Countdown Timer

Advanced Operation

Using Rewind-Say-Again to Record Audio Transmission

1.Press and hold SCAN button for two (2) seconds to enter Record mode.

2.Press and hold Talk button to begin recording from radio microphone. If Talk button is released, recording stops. While recording, a 20-second countdown begins on display. When 20-second countdown time has ended, recording stops and two (2) beep tones will be heard.

3.Press and hold the SCAN button again for two (2) seconds or press MEM/ESC button to cancel recording and return to last operation.

NOTE

When using radio in Record mode, the REW feature is turned Off to prevent “recording over” previous message.

Nothing Comes Close to a Cobra® 53

Image 58

Contents MR HH415LI VP EU Our Thanks to You and Customer Assistance Radio Controls and Indicators LCDBacklit LCD Screen and Product Features Product Features Speaker/Mic JackTable of Contents Important Safety Information Important Safety InformationGeneral Precautions Important Safety Information Recommendations for Marine Communication Recommendations for Marine CommunicationCanadian or U.S.A. Station License Licensing InformationStation License Radio Call SignVHF Marine Radio Procedures Voice Calling Voice CallingVessel Corsair calling the vessel Vagabond Radiotelephone Calls Radiotelephone CallsEmergency Messages and Distress Procedure Emergency Messages and Distress ProcedureMarine Emergency Signals If You Hear a Distress CallSay Marine Distress ProcedureTell where you are End message by sayingFor Example VHF Marine Channel Assignments Navigational Public Correspondence marine operatorPort Operations Digital Selective CallingUSA International Distress, Safety and Calling 03A Government Only156.900 23A Government Only 21A U.S. Government Only Canada Coastguard Only61A U.S. Government Only Canada Coastguard Only Channel 64A U.S. Government Only Canada Commercial Fishing Digital Selective Calling Voice communications not allowedLimits 81A U.S. Government Only Environmental Protection Operations Included in this Package Included in this PackageWrist Strap Antenna InstallationAntenna, Wrist Strap and Belt Clip Belt ClipBatteries and Charger Installing the Battery PackBatteries and Charger Initial Charge To Remove Battery Pack from Radio Alkaline BatteriesMaintaining the Battery Charge Getting Started Power/Volume/Squelch Controls Power On/Off ControlVolume Control Common Radio FunctionsSquelch Control Talk ButtonTo Display the Backlight Momentarily TRI-WATCH Button Call/Enter/Setup Button Preset ButtonBacklight/Key Lock Button Key LockScan Button To Toggle Between H-M-L Power Modes High/Medium/Low H-M-L Power ButtonCall /Enter/Setup Button To Set Personal Default Settings International/Canada/USA Channel Maps Setup Mode ProgrammingSetup Mode Programming To Set Channel Map Operating AreaVibrAlert Mode To set VibrAlertCall Tone Mode To Set Call ToneTo Set Roger Beep On or Off Roger Beep ModeKey Tone Mode To Set Key Tone On or OffAtis ID Programming Atis ID ProgrammingTo Set the Atis ID Number Atis ID Programming Marine Standby and Receive Rx Mode Standby/Receive and TransmitStandby/Receive Transmit Transmit Tx ModeTo Transmit a Message Advanced Operation Channel 16 ModeTo Switch to Channel Advanced OperationTri-Watch Mode Tri-Watch Setup To Program or Edit the Tri-Watch ChannelsUsing Tri-Watch Tri-Watch Scan Mode Tri-Watchmemory channelsMemory Location Mode To Program Memory LocationsTo Recall a Stored Memory Location To Exit Memory Location ModeTo Erase Stored Memory Locations Channel Scan Mode To Enter Channel ScanMemory Location Scan Mode To Enter Memory Location Scan From Marine Standby mode, press the MEM/ESC buttonUsing Rewind-Say-Again Rewind-Say-Again FeatureExample Using Rewind-Say-Again to Record Audio Transmission Press Backlight MaintenanceTroubleshooting Key Lock buttonSpecifications SpecificationsEnglish Accessories AccessoriesLapel Speaker/Microphone Declaration of Conformity and CE Marking