Uniden EXAI3985 manual Choose the dialing mode, Base Setting only

Page 11

D. Choose the dialing mode

Most phone systems use tone dialing, which sends DTMF tones through the phone lines. However, some phone systems still use pulse dialing such as in rural areas. The default setting is tone dialing. Depending on your dialing system, set the mode as follows:

Base Setting only

1	Press and hold flash/set until you hear a confirmation tone.
2	To set the dial mode for pulse dialing, press				# . Or to set the dial
	mode for tone dialing, press			. A confirmation tone sounds to

	indicate the setting is complete.

•If you are not sure of your dialing system, set for tone dialing. Make a trial call. If the call connects, leave the setting as is, otherwise set for pulse dialing.

•If your phone system requires pulse dialing and you need to send the DTMF tones for certain situations during a call, you may “switch-over” to tone dialing (refer to “Tone Dialing Switch-over” on page 31).

note

Make sure your battery pack is fully charged before choosing the dialing mode.

G E T T I N G S T A R T E D

G E T T I N G S TA R T E D [ 9 ]

Image 11

Contents Page Page Contents Explanation purposes FeaturesWelcome Flash Controls and FunctionsO N T R O L S a N D F U N C T I O N S Checking the Package Contents Choose the best location Setting up the PhoneDo the following steps Low battery alert Install the battery packBattery use time per charge Connect the base unit Press and hold flash/set until you hear a confirmation tone Choose the dialing modeBase Setting only Standard wall plate mounting Setting the handset retainer clip for wall mountingDirect wall mounting Use Or ª To move the pointer to the selection Setting Caller ID OptionsTo make your selections and a confirmation tone Or Cidcw Off depending upon the type of service to whichUse To move the pointer between Auto Talk On or You subscribe PressHandset ringer volume setting Handset Ringer Volume SetupHandset Ringer Tone Setting A confirmation tone will sound Distinctive Ringer SetupAppears Selecting a LanguageHandset Off the Base Making and Receiving CallsFrom the Handset From the Base Handset On the Base Call Waiting. See Adjusting Earpiece VolumeBase Volume Call WaitingRedialing a Call Redialing from Standby ModeRedial from Talk Mode From the Base Traveling Out-of-RangeKeypad to enter the name. Press With the handsetStore Name appears on Display. Then use the numberE M O R Y D I a L I N G With the Base Memory dialing from Standby Mode With the handsetMaking Calls with Memory Dialing Press talk . Talk Memory dialing from Talk ModeDisplay a programmed number while in memory location list Press , ª to scroll through memory locations To selectPress to move the pointer to Yes Editing a stored name, phone number or distinctive ringDeleting the stored data With the Base Way Conferencing When speaking on the handsetWhen speaking on the base Base. The handset beeps. If no answer, press Intercom/Page FeatureIntercom from the base to the handset Intercom from the handset to baseTo transfer from the base to the handset Call Transfer FeatureChain Dialing To transfer from the handset to the baseSelecting a Different Channel Tone Dialing Switch-overMute Handset/Base Caller ID When the Telephone RingsYou must subscribe to Caller ID service to use this feature Press caller id to return to standby When you answer the call, the display changes to TalkViewing the Caller ID Message List Deleting a Caller ID message When the pointer is at YesWhen the pointer is at No Deleting Information from the Caller ID ListTone sounds and all stored Caller ID messages are deleted Using the Caller ID ListDeleting all Caller ID names/numbers Calling a party from the Caller ID listStoring Caller ID messages in memory dialing Long distance calls and area code setting/cancellationName of the caller are displayed Using Caller ID on Call Waiting ServiceWhen a new incoming call arrives during your Current telephone call, the phone numberFor example Call Waiting Deluxe FeaturesIntegrated Answering Device Turning the Answering System On/Off Setting up your Answering SystemUsing the Menu Mode Choosing between the two outgoing messages Setting Your Outgoing Message GreetingPreset message Recording a personal outgoing message GreetingTo select the minute Setting the TimeSetting a Personal Security Code You hear the current ringer option High Setting the base ringer volumeAdjusting the speaker volume level Four timesSetting the Ring Time Selecting the message record time Announce only featurePlaying your messages Using your Answering SystemSkipping a message Repeating a messageVoice memo Deleting a messageTo stop recording, press or memo/rec Remote access away from homeRecording a conversation Command You may select a command from the following chartTurn on the answering system remotely Changing the Digital Security Code To remove the Face plate To attach the Face plate Headset InstallationChanging the Face Plate Maintenance Installing the BeltclipPower Failure Battery replacement and handlingSymptom TroubleshootingSymptom Suggestion AC Adapter Information Battery InformationGeneral Information Precautions Installation Considerations K, L IndexRemote Operation Card Remote access away from homeTask Key At Uniden, we’ll take care of you