Uniden EXAI3985 manual Install the battery pack, Battery use time per charge, Low battery alert

Page 9

B. Install the battery pack

Place the handset on the base unit and charge the battery pack for at least 15-20 hours before plugging the phone line into your phone.

Battery use time (per charge)

From fully charged:

•6 hours continuous use.

•10 days when the handset is in the standby mode.

Low battery alert

If the phone is not in use, “Low Battery” appears on the LCD and none of the keys will operate. If the phone is in use, “Low Battery” flashes and the handset beeps. Complete your conversation as quickly as possible and return the handset to the base unit

for charging.

note

•Use only the Uniden Battery supplied with your phone. Replacement batteries are also available through the Uniden Parts Department (See page 59) or www.uniden.com

•Even when the battery pack is not being used, it will gradually discharge over a long period of time. For optimum performance, be sure to return the handset to the base unit after each telephone call.

•If you must replace the battery pack during a telephone call, complete the replacement of the battery pack within 30 seconds, and you can return to the original call.

G E T T I N G S T A R T E D

G E T T I N G S TA R T E D [ 7 ]

Image 9

Contents Page Page Contents Features WelcomeExplanation purposes Flash Controls and FunctionsO N T R O L S a N D F U N C T I O N S Checking the Package Contents Setting up the Phone Do the following stepsChoose the best location Install the battery pack Battery use time per chargeLow battery alert Connect the base unit Choose the dialing mode Base Setting onlyPress and hold flash/set until you hear a confirmation tone Standard wall plate mounting Setting the handset retainer clip for wall mountingDirect wall mounting Use Or ª To move the pointer to the selection Setting Caller ID OptionsUse To move the pointer between Auto Talk On or Or Cidcw Off depending upon the type of service to whichYou subscribe Press To make your selections and a confirmation toneHandset Ringer Volume Setup Handset Ringer Tone SettingHandset ringer volume setting A confirmation tone will sound Distinctive Ringer SetupAppears Selecting a LanguageMaking and Receiving Calls From the Handset From the Base Handset On the BaseHandset Off the Base Base Volume Adjusting Earpiece VolumeCall Waiting Call Waiting. SeeRedialing from Standby Mode Redial from Talk ModeRedialing a Call From the Base Traveling Out-of-RangeStore Name appears on With the handsetDisplay. Then use the number Keypad to enter the name. PressE M O R Y D I a L I N G Memory dialing from Standby Mode With the handset Making Calls with Memory DialingWith the Base Memory dialing from Talk Mode Display a programmed number while in memory location listPress talk . Talk Press , ª to scroll through memory locations To selectEditing a stored name, phone number or distinctive ring Deleting the stored dataPress to move the pointer to Yes With the Base When speaking on the handset When speaking on the baseWay Conferencing Intercom from the base to the handset Intercom/Page FeatureIntercom from the handset to base Base. The handset beeps. If no answer, pressChain Dialing Call Transfer FeatureTo transfer from the handset to the base To transfer from the base to the handsetTone Dialing Switch-over Mute Handset/BaseSelecting a Different Channel When the Telephone Rings You must subscribe to Caller ID service to use this featureCaller ID When you answer the call, the display changes to Talk Viewing the Caller ID Message ListPress caller id to return to standby When the pointer is at No When the pointer is at YesDeleting Information from the Caller ID List Deleting a Caller ID messageDeleting all Caller ID names/numbers Using the Caller ID ListCalling a party from the Caller ID list Tone sounds and all stored Caller ID messages are deletedStoring Caller ID messages in memory dialing Long distance calls and area code setting/cancellationWhen a new incoming call arrives during your Using Caller ID on Call Waiting ServiceCurrent telephone call, the phone number Name of the caller are displayedFor example Call Waiting Deluxe FeaturesIntegrated Answering Device Setting up your Answering System Using the Menu ModeTurning the Answering System On/Off Preset message Setting Your Outgoing Message GreetingRecording a personal outgoing message Greeting Choosing between the two outgoing messagesTo select the minute Setting the TimeSetting a Personal Security Code Adjusting the speaker volume level Setting the base ringer volumeFour times You hear the current ringer option HighSetting the Ring Time Selecting the message record time Announce only featurePlaying your messages Using your Answering SystemSkipping a message Repeating a messageVoice memo Deleting a messageRemote access away from home Recording a conversationTo stop recording, press or memo/rec Command You may select a command from the following chartTurn on the answering system remotely Changing the Digital Security Code Headset Installation Changing the Face PlateTo remove the Face plate To attach the Face plate Maintenance Installing the BeltclipPower Failure Battery replacement and handlingSymptom TroubleshootingSymptom Suggestion Battery Information General InformationAC Adapter Information Precautions Installation Considerations K, L IndexRemote Operation Card Remote access away from homeTask Key At Uniden, we’ll take care of you