Heat Controller DMC24DB-1, DMH36TB-1 Flaring work, Cut the pipes and the cable, Burrs removal

Page 12

Flaring Work and Connection of Piping

Flaring Work and Connection of Piping

Flaringwork

Main cause for gas leakage is due to defect in flaring work. Carry out correct flaring work in the following procedure.

Cut the pipes and the cable.

1.Use the piping kit accessory or the pipes purchased locally.

2.Measure the distance between the indoor and the outdoor unit.

3.Cut the pipes a little longer than measured distance.

4.Cut the cable 1.5m (5.0ft) longer than the pipe length.

Burrs removal

1.Completely remove all burrs from the cut cross section of pipe/tube.

2.Put the end of the copper tube/pipe in a downward direction as you remove burrs in order to avoid dropping burrs into the tubing.

Putting nut on

Remove flare nuts attached to indoor and outdoor unit, then put them on pipe/tube having completed burr removal.

(not possible to put them on after flaring work)

Copper

 

Slanted

Uneven Rough

pipe

90°

 

 

Pipe

 

 

 

Reamer

Point down

Flare nut

Copper tube

Flaring work

Carry out flaring work using flaring tool as shown below.

Firmly hold copper pipe in a die in the dimension shown in the table above.

Outside diameter

A

 

 

 

mm

inch

mm

Ø6.35

1/4

0~0.5

Ø9.52

3/8

0~0.5

 

"A"

 

Handle

Bar

Bar

 

 

Yoke

 

 

 

 

 

 

Cone

 

Copper pipe

 

 

 

Clamp handle

Red arrow mark

 

 

 

12Room Air Conditioner

Image 12
Contents DMC24DB-1, DMH24DB-1 DMC36TB-1, DMH36TB-1 Table of Contents Installation Parts Provided 24k36k Safety Precautions Be sure not to do Be sure to follow the instructionThere is risk of fire, electric shock, explosion or injury Could cause personal injury Personal injury Moisture may condense and wet or damage furnishingsThere is risk of fire or product failure Oxygen deficiency could occurThere is risk of fire or electrical shock There is risk of electric shockThere is risk of electrical shock There could result in personal injury and product damageIt may cause a problem for your neighbors Avoid personal injuryThis could damage your health There is risk of damage or loss of propertyIt is not sanitary and could cause serious health issues There is risk of personal injuryThere is risk of personal injury and failure of product Be careful and avoid personal injuryInstallation of Indoor, Outdoor Unit Rooftop InstallationsSelect the best location Indoor unitPiping length and elevation Multi Piping Type24k 36k Fixing Installation Plate Drill a hole in the wallFlaring work Cut the pipes and the cableBurrs removal Putting nut onConnecting the Piping CheckIndoor Foamed polyethylene or equivalent is recommendedIndoor unit installation Outside diameter TorqueKg .mlbf .ft Flare nut PipesIndoor unit Spacer Open-end wrench fixed Flare nut WrenchIndoor unit tubing Piping for Piping holeGood case Bad caseOutdoor Outside diameter TorqueConnect the cable to the Indoor unit Power supply Connect the cable to the Outdoor unitWith the screw How to connect wiring to the terminals Circuit Breaker MOC rating on the unit rating plate Checking the drainage To check the drainageDrain piping Pour a glass of water on the evaporatorForming the piping Seal a small Opening around Pipings withGum type sealer Air Purging and Evacuation Checking methodRepeat evacuation procedure for each indoor unit EvacuationFinishing the job Charging Max totalAdditional Prepare remote control Test RunningEvaluation of the performance Heat CONTROLLER, INC
Related manuals
Manual 70 pages 47.27 Kb Manual 35 pages 26.68 Kb Manual 25 pages 18.28 Kb

DMC24DB-1, DMH24DB-1 DMC36TB-1, DMH36TB-1 specifications

The Heat Controller DMH24DB-1 and DMC24DB-1 units stand out in the realm of climate control solutions, combining advanced technology with user-friendly features to enhance indoor comfort. These air conditioning systems are designed to provide efficient cooling and heating for both residential and commercial spaces.

One of the main features of the DMH24DB-1 and DMC24DB-1 is their inverter technology. This cutting-edge technology allows the units to adjust the compressor speed according to the cooling demands of the space, leading to significant energy savings. By operating at variable speeds instead of a fixed setting, the inverter provides a more consistent temperature, reduces wear and tear on components, and minimizes energy consumption, which can translate to lower electricity bills.

Both models offer a sleek and modern design, making them not only functional but also aesthetically pleasing. The indoor units are designed for easy placement in various environments and can blend seamlessly with any decor. In addition, they are relatively quiet during operation, with low noise levels that enhance indoor comfort without disturbing daily activities.

Another notable feature is the integrated smart control system that allows users to operate the units via a smartphone or tablet. This capability offers the convenience of adjusting settings from anywhere, ensuring that your space is always at the desired temperature when you arrive home or the office. The app can provide insights into energy consumption, allowing users to make informed decisions about their heating and cooling usage.

The DMH24DB-1 and DMC24DB-1 models also boast efficient filtration systems that help improve indoor air quality. The filters are designed to capture dust, pollen, and other allergens, contributing to a healthier living or working environment. This is particularly important for individuals with allergies or respiratory issues.

With a variety of cooling and heating modes, these units can cater to different user preferences and seasonal demands. Features like turbo mode are designed to quickly bring a space to the desired temperature, while the eco-friendly refrigerant helps reduce environmental impact.

In summary, the Heat Controller DMH24DB-1 and DMC24DB-1 units are high-performance air conditioning systems equipped with advanced technologies and practical features, making them an excellent choice for anyone seeking efficient and reliable climate control solutions. Their energy efficiency, enhanced air quality, and smart technology integration position them as leaders in the market.