Connecting the Cable between Indoor Unit and Outdoor Unit
ConnectthecabletotheOutdoorunit.
1. Remove the cover control from the unit by |
|
|
| Outdoor unit | ||||||||||||
loosening the screw. |
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
| |||||||
Connect the wires to the terminals on the |
|
|
| Terminal block | ||||||||||||
control board individually as the following. |
|
|
| |||||||||||||
|
|
| Over 5mm | |||||||||||||
2. Secure the cable into the control board with |
|
| ||||||||||||||
|
|
| ||||||||||||||
the strain relief clamp. |
|
|
|
|
|
|
|
|
| Holder for | ||||||
3. Refix the cover control to the original position |
|
| power supply | |||||||||||||
|
| cord | ||||||||||||||
with the screw. |
|
|
|
|
|
|
|
|
|
|
| Power supply | ||||
|
|
|
| 24k Outdoor side |
|
|
|
|
|
|
| cable | ||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
| 1 | 2 | 3 |
| 4 | 1 | 2 | 3 | 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Cover control |
|
|
|
|
|
| Connecting cable(Low voltage) |
|
|
|
|
| Connecting | ||||
|
|
|
|
|
|
|
|
|
|
| cable | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| L |
| N |
|
|
|
|
|
|
|
|
|
1 | 2 | 3 | 4 |
|
|
|
|
| 1 | 2 | 3 | 4 |
|
|
|
|
Terminal BLOCK |
| Power Source |
| Terminal BLOCK |
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Indoor |
| 208/230V AC |
| Indoor |
|
|
|
| ||||||||
| (High voltage) |
|
|
|
|
| ||||||||||
|
|
| 36k Outdoor side |
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |||||||
|
| 1 | 2 | 3 | 4 | 1 | 2 | 3 | 4 |
|
|
| 1 | 2 | 3 | 4 |
|
|
|
|
|
|
| Connecting cable(Low voltage) |
|
|
|
| |||||
|
|
|
| L |
|
| N |
|
|
|
|
|
|
|
|
|
1 | 2 | 3 | 4 |
|
|
|
| 1 | 2 | 3 |
| 4 | 1 | 2 | 3 | 4 |
Terminal BLOCK | Power Source | Terminal BLOCK |
| Terminal BLOCK |
Indoor | 208/230V AC | Indoor |
| Indoor |
(High voltage) |
|
NOTICE :
1.Separately wire the high and low voltage line.
2.Use
3.Use outdoor and waterproof connection cable rated more than 300V for the connection between indoor and outdoor unit. (For example, Type SJOW)
WARNING:
•Be sure to comply with local codes while running the wire from the indoor unit to the outdoor unit(size of wire and wiring method, etc).
•Every wire must be connected firmly.
•No wire should be allowed to touch refrigerant tubing, the compressor or any moving parts.
20Room Air Conditioner