Heat Controller DMH36TB-1 Test Running, Prepare remote control, Evaluation of the performance

Page 28

Test Running

Test Running

1.Check that all tubing and wiring have been properly connected.

2.Check that the gas and liquid side service valves are fully open.

Prepare remote control

Remove the battery cover by pulling it according to the arrow direction.

Insert new batteries making sure that the (+) and

(–)of battery are installed correctly. Reattach the cover by pushing it back into position.

NOTICE :

•Use 2 AAA(1.5volt) batteries. Do not use rechargeable batteries.

•Remove the batteries from the remote control if the system is not going to be used for a long time.

Bolt

Tubing connection

Evaluation of the performance

Operate all indoor units for 15~20 minutes, then

Intake temperature

check the system refrigerant charge:

 

1.Measure the pressure of one of the gas side

Discharge air

service valves.

 

 

 

2. Measure the temperature of the intake and

 

discharge of air.

 

 

3. Ensure the difference between the intake

 

temperature and the discharge is more than

 

8°C(14.4°F).

 

Discharge

4. For reference, the gas side pressure of

temperature

 

optimum condition is as below.(Cooling)

 

Refrigerant

Outside ambient

The pressure of the gas side

 

 

TEMP.

service valve.

 

R-410A

35°C (95°F)

8.5~9.5kg/cm2G(120~135 P.S.I.G.)

 

NOTICE : If the actual pressure are higher than shown, the system is most likely over-charged, and charge should be removed. If the actual pressure are lower than shown, the system is most likely undercharged, and charge should be added.

NOTICE : For maximum product life and efficiency this unit has been designed, in the heating mode, to lock-out at outdoor temperatures below 26-29°F.

At outdoor temperatures below 26-29°F. another means of heating the conditioned space must be provided.

Important:

❏Individual zones should be all in the same operation mode (Heating or Cooling mode)

28Room Air Conditioner

Page 27 Page 29
Image 28
Page 27 Page 29
Contents DMC24DB-1, DMH24DB-1 DMC36TB-1, DMH36TB-1 Table of Contents 24k Installation Parts Provided36k Be sure not to do Be sure to follow the instruction Safety PrecautionsThere is risk of fire, electric shock, explosion or injury Could cause personal injury Personal injury Moisture may condense and wet or damage furnishingsThere is risk of fire or product failure Oxygen deficiency could occurThere is risk of fire or electrical shock There is risk of electric shockThere is risk of electrical shock There could result in personal injury and product damageIt may cause a problem for your neighbors Avoid personal injuryThis could damage your health There is risk of damage or loss of propertyIt is not sanitary and could cause serious health issues There is risk of personal injuryThere is risk of personal injury and failure of product Be careful and avoid personal injuryInstallation of Indoor, Outdoor Unit Rooftop InstallationsSelect the best location Indoor unitMulti Piping Type Piping length and elevation24k 36k Fixing Installation Plate Drill a hole in the wallFlaring work Cut the pipes and the cableBurrs removal Putting nut onConnecting the Piping CheckIndoor Foamed polyethylene or equivalent is recommendedIndoor unit installation Outside diameter TorqueKg .mlbf .ft Flare nut PipesOpen-end wrench fixed Flare nut Wrench Indoor unit SpacerIndoor unit tubing Piping for Piping holeGood case Bad caseOutdoor Outside diameter TorqueConnect the cable to the Indoor unit Connect the cable to the Outdoor unit Power supplyWith the screw How to connect wiring to the terminals Circuit Breaker MOC rating on the unit rating plate Checking the drainage To check the drainageDrain piping Pour a glass of water on the evaporatorSeal a small Opening around Pipings with Forming the pipingGum type sealer Air Purging and Evacuation Checking methodEvacuation Repeat evacuation procedure for each indoor unitFinishing the job Max total ChargingAdditional Test Running Prepare remote controlEvaluation of the performance Heat CONTROLLER, INC
Related manuals
Manual 70 pages 47.27 Kb Manual 35 pages 26.68 Kb Manual 25 pages 18.28 Kb

DMC24DB-1, DMH24DB-1 DMC36TB-1, DMH36TB-1 specifications

The Heat Controller DMH24DB-1 and DMC24DB-1 units stand out in the realm of climate control solutions, combining advanced technology with user-friendly features to enhance indoor comfort. These air conditioning systems are designed to provide efficient cooling and heating for both residential and commercial spaces.

One of the main features of the DMH24DB-1 and DMC24DB-1 is their inverter technology. This cutting-edge technology allows the units to adjust the compressor speed according to the cooling demands of the space, leading to significant energy savings. By operating at variable speeds instead of a fixed setting, the inverter provides a more consistent temperature, reduces wear and tear on components, and minimizes energy consumption, which can translate to lower electricity bills.

Both models offer a sleek and modern design, making them not only functional but also aesthetically pleasing. The indoor units are designed for easy placement in various environments and can blend seamlessly with any decor. In addition, they are relatively quiet during operation, with low noise levels that enhance indoor comfort without disturbing daily activities.

Another notable feature is the integrated smart control system that allows users to operate the units via a smartphone or tablet. This capability offers the convenience of adjusting settings from anywhere, ensuring that your space is always at the desired temperature when you arrive home or the office. The app can provide insights into energy consumption, allowing users to make informed decisions about their heating and cooling usage.

The DMH24DB-1 and DMC24DB-1 models also boast efficient filtration systems that help improve indoor air quality. The filters are designed to capture dust, pollen, and other allergens, contributing to a healthier living or working environment. This is particularly important for individuals with allergies or respiratory issues.

With a variety of cooling and heating modes, these units can cater to different user preferences and seasonal demands. Features like turbo mode are designed to quickly bring a space to the desired temperature, while the eco-friendly refrigerant helps reduce environmental impact.

In summary, the Heat Controller DMH24DB-1 and DMC24DB-1 units are high-performance air conditioning systems equipped with advanced technologies and practical features, making them an excellent choice for anyone seeking efficient and reliable climate control solutions. Their energy efficiency, enhanced air quality, and smart technology integration position them as leaders in the market.
Top Page Image Contents