INMOTION PORTABLE AUDIO SYSTEM
Thank you for purchasing this Altec Lansing product. For generations, Altec Lansing has been first in audio innovation. Today, our line of powered speakers has received more performance awards than any other brand. In all kinds of desktop environments, in every price range, Altec Lansing offers sound of distinction — giving even the most demanding customers the audio enjoyment they seek. Just listen to this!
BOX CONTENTS
•inMotion portable audio system
•Universal Power Supply
•3.5mm Stereo Cable
•Protective Case
•10GB/15GB iPod Docking Spacer
•Docking Connector Travel Cover
•Manual
•Quick Connect Card (may be located on internal box flaps)
PLACING THE INMOTION SYSTEM
Position the inMotion system on a level surface preferably close to you (within three feet). The inMotion system can be placed close to video displays such as TVs and computer monitors without distorting the image.
MAKING CONNECTIONS
Warning: Do not insert the speaker system’s universal power supply into a wall outlet until all connections are made. Also, turn off your iPod before docking on the inMotion system.
To ensure
Newer iPods can be connected to the inMotion system via the docking port, while older iPods must be connected using the auxiliary input jack. These are the only signal input connections that need to be made. After either of these connections are made, insert the barrel connector from the universal
power supply into the connector marked 
on the rear of the inMotion system. After this connection is made, insert the universal power supply into a wall outlet. You can now use your speakers.
Please note, the inMotion system can also be powered with four AA batteries (not included). Make sure the batteries are installed as illustrated in the battery compartments found on the bottom of the inMotion system.
HEADPHONES
To use headphones with the system, plug them into the jack labeled 
on the rear of the inMotion system. When headphones are connected, all external speakers are muted.
POWERING ON
AC POWER
After your iPod is docked on the inMotion system, plug the universal power supply into a wall outlet. The speaker system is now ready to operate.
1.Turn on your iPod
2.Turn on the Altec Lansing inMotion system by sliding the power switch
located on the front panel 
to the right. A green LED will light next to the switch when the power is on.
Note: To avoid hearing a popping sound when you turn on your Altec Lansing speaker system, always turn on your audio source first.
DC (BATTERY) POWER
Install four AA batteries (not included) into the battery compartments on the bottom of the inMotion system (two to each compartment). Make sure the batteries are installed as illustrated in the battery compartments. After your iPod is docked on the inMotion system, the speaker system is ready to operate.
1.Turn on your iPod
2.Turn on the Altec Lansing inMotion system by sliding the power switch located on the front panel 
to the right. A green LED will light next to the button when the power is on. The LED will turn amber in color to indicate the batteries must be replaced.
Note: To avoid hearing a popping sound when you turn on your Altec Lansing speaker system, always turn on your audio source first.
VOLUME
The 
buttons on the front of the inMotion system are the master volume controls for the speaker system. Press and hold the “+” button to increase the volume and the
SYSTEM SPECIFICATIONS
Altec Lansing’s superior sound comes from our patented technology, which utilizes
| Total Continuous Power: | 4 | Watts RMS |
| POWER REQUIREMENTS |
|
|
|
|
|
|
|
|
|
|
| • Front Speakers: | 2 | Watts/channel @ 8 ohms |
| USA, Canada and applicable |
|
|
|
| @ 10% THD+N @ 20 – 20 kHz |
| Latin American countries: | 120 V AC @ 60 Hz | ||
|
| 2 | Channels Loaded |
|
|
|
|
|
|
|
|
|
|
|
|
| Frequency Response: | 60 Hz – 20kHz |
| Europe, United Kingdom, |
|
| |
|
|
|
|
|
|
| |
| Signal to Noise Ratio |
|
|
| applicable Asian countries, |
|
|
| @ 1 kHz input: | > 75 dB |
| Argentina, Chile and Uruguay: | 230 V AC @ 50 Hz | ||
|
|
|
|
|
|
| |
| Drivers: | Four 1" |
| ETL/cETL/CE/NOM/IRAM Approved |
|
| |
|
| neodymium microdrivers |
|
|
|
| |
|
|
|
|
|
|
|
|
2