JVC HM-HDS1U manual Access DBS Receiver, SET DBS Receiver Brand

Page 20

20 EN

Turn on the TV and select the AV mode.

INITIAL SETTINGS (cont.)

ACCESS DBS RECEIVER

BRAND SET SCREEN

7 Press # (or 3) or OK.

SET DBS RECEIVER BRAND

Press the appropriate

NUMBER keys to enter DBS RECEIVER BRAND SET

8 the DBS Receiver Code

POWER

HM-HDS1

MENU	EJECT
	DIGITPURE TECHNOLOGY

REC LINK		STOP	PLAY	PAUSE	REC	S-VHS ET
		HDD				S-VHS		VIDEO	(M) L – AUDIO – R
MENU	NAVI					REW	FEW
OK									S-VIDEO
	CH					A. DUB			PAUSE
								F - 1

OK

from the following list,

then press # (or 3) or
OK.
	PRESS NUMBER KEY(0-9)
	THEN(OK) TO TEST
	PRESS(MENU) TO END



BRAND			CODE
JVC (DISH Network)		51
ECHOSTAR (DISH Network)		51
PRIMESTAR		50
SONY (DSS)		41
RCA (DSS)		40

●After OK is pressed, the program currently received through the DBS receiver will appear for about 10 seconds.

●If the DBS receiver's channel changes to the channel listed below for your brand of DBS receiver, setting is complete. Press OK and “DBS RECEIVER CONTROL IS ON” appears on the screen for about 5 seconds, then it returns to the Initial Set Up screen. To returns to the normal screen, press MENU.

	1
	2
	1	2	3
NUMBER	4	5	6
NUMBER
	7	8	9
	<	0	>
	1
	2

OK

– +

3

4

MENU

OK

JVC [ 100

ECHOSTAR [ 100

PRIMESTAR [ 55

SONY [ 205

RCA [ 205

●If the DBS receiver's channel does not change as shown above, press %ﬁ (or 5∞) repeatedly until “NO” appears, then press OK. Re-enter the correct code.

NOTES:

●It is possible that the Controller will not work with all types of DBS receiver.

●If your DBS receiver doesn’t respond to the code, you can’t use the Controller to change satellite channels. In this case, make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.

●The recorder can only change the satellite channel through the Controller during timer recording.

●If your DBS receiver is one that can’t be operated with a remote control (because it has no remote sensor), you can’t use the Controller to change its channels. Make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.

●If you are unable to set the Controller, please contact JVC toll free at 1-800-252-5722.

Image 20

Contents HM-HDS1U Dear Customer Do not place the recorderInstallation Antenna Installation Instructions USEBefore YOU Install Your NEW Recorder ServicingWhile using the recorder Before installing the recorderBefore using the recorder Contents Check Contents Power SourceConnections Situate RecorderPlug & Play Setup Plug & PlayAuto Clock Set/Auto Tuner Set Auto blinks Channel numbers are displayedAccess Main Menu Access Initial SET ScreenAccess Clock SET ClockSelect D.S.T. Mode SET Auto Clock to onSelect Host Channel Select Time ZoneSET Time SET DateSET Year ManualAccess Tuner SET Screen TunerTurn on the Recorder Set Receivable ChannelsAccess Main Menu Screen Access Tuner SET ScreenAccess Manual Channel SET Screen ADD or Skip DesiredCable Box Control Situate ControllerAttach Controller Connect Cable BOX to RecorderSelect Cable BOX Output Channel Access Cable BOX SET ScreenTurn on Cable BOX Access Cable BOX Brand SET Screen Enter Cable BOX BrandFasten securely using the supplied adhesive strips DBS Receiver ControlController DBS receiverAccess DBS Receiver SET Screen At the Initial Set UpTurn on DBS Receiver Set DBS Receiver Output Channel & DBS Receiver BrandAccess DBS Receiver SET DBS Receiver BrandSelect Blue Back Mode Setting Blue BackAccess Function Setting Video Inputs Mode Access Video Inputs ScreenSelect Video Inputs ModeSimple Recording Simple Playback Start PlaybackPause Playback Stop PlaybackPlayback with HDD Navigation Icons and their meaningsScan for Beginnings of Programs Access Scan ScreenSelect Programs Setting Time for Live Memory Playback Live Memory PlaybackStart Live Memory Playback About Live Memory PlaybackAccess Function Screen SuperimposeArrow to Superim Pose by pressingTo Recall Indication Playback Features Change Speed Activate Quick SkipVariable-Speed Search/ Reverse Motion Playback Quick Rewind a littleSelect The Soundtrack Start RewindRepeat Playback Normal Playback Only Recording Features Engage TV ModeSelect Channel for ViewingLoad a Cassette Select VHS DeckFind Program Start PointRecording SET Tape SpeedPAUSE/RESUME Playback with VHS Navigation Set VHS Navigation Access VHS SET UPSelect VHS Navigation Mode Scan for Beginning of Pro- gram with VHS Navigation Tered ProgramSelect Program Change SLOW-MOTION Speed Activate HIGH-SPEED SearchActivate FRAME-BY Index Search Access Distant CodeStart Search Tuned-in channel or AUXiliary mode Operation modeSwitchable to the tape remaining time display Press OSDTracking Mode Adjust ManualEngage Manual TrackingCounter Reset Tape Position IndicatorPress C.RESET Beginning or E End shows you Where you are on the tapePicture Control Access VHS SET UP 1 ScreenSelect Picture Control Mode Video Stabilizer Access VHS SET UP ScreenSelect Video Stabilizer Mode Select TBC Mode TBC byPressing Arrow to %ﬁ ∞, then press OKCalibration Mode At the top of the HDD/VHS SET UPActive Video Calibration Calibration byRecording Display Counter Information Display Tape Remaining TimeExit the Display Display Elapsed Recording TimeVHS Super VHS, S-VHS ET and VHS Engage S-VHS ET Mode Super VHS ETResume Recording Engage RECORD-PAUSE ModeLocate Start Point To Listen To Stereo Soundtrack During Recording Stereo And SAP Second Audio ProgramTo Record Stereo Programs VCR Plus+ Timer Programming Check Program Data Changing VCR Plus+ Setting Access Initial SETInitial SET UP by VCR Plus+ Guide Channel MatchingAccess Guide Channel SET Screen Input Receiving ChannelExpress Timer Programming Recorded onSET Program Date SET Program Stop TimeSET Category SET Channel NumberSET Weekly or Daily Check Overlap Program Return to the NormalSTOP+/-,DATE+ CH+CH+ Check, Cancel And Revise ProgramsVHS Deck only Select Auto SP=EP Timer Mode Auto SP→EP TimerTimer Recording Prepare the External Equipment for Timer RecordingEngage REC Link Mode To cancel REC Link mode, press REC Link againInstant Timer Recording ITR Engage ITR ModeSET Recording DurationAbout Hybrid Navigation About Registration of InformationAbout Editing of Programs Limitations of RegistrationAccess Modify Screen Modify InformationSelect Deck Register NEW IndexAccess Navigation Screen Enter NEW TitleRegister NEW Title Modify Program TitleSelect NEW Category Register NEW CategoryModify Category Press @%#ﬁ or 253∞ to move the arrow toAccess Delete Screen Confirm DeletionDelete Information For HDD NavigationAccess Easy Dubbing DubbingNavigation Screen Select Dubbing OptionSelect REC Speed Start DubbingEND Dubbing Normal DubbingDubbing Press Pause on the remote control. To resume Remote controlDard at the VHS SET UP 1 of the main Menu Press VHS or S-VHS and select the program to beRandom Assemble Editing Program Editing Memory 1 program x 8 scenesSelect the Other EDIT-IN and EDIT-OUT Points Prepare VHS Deck forRecording Start EditingEdit From a CamcorderReturn to Normal Screen Start PlayerStart Recorder For HDD deckLoad Cassettes Edit To Or From AnotherMake Connections SET RECORDER’S Input Mode Select Edit for PICStart Player Start RecorderSET Input Mode Audio DubbingEngage Audio Dubbing VHS Audio DubbingWhen monitoring the sound during Audio Dubbing, END Audio DubbingSET Remote Control TV Multi-Brand Remote ControlTurn on the TV SET TV Brand CodeHDD or VHS or S-VHS Cable Box Multi-Brand Remote ControlOperate Cable BOX DBS Receiver Multi-Brand Remote Control Turn on the DBSReceiver Enter DBS Receiver BrandSET Remote Control Code Enter Remote Control CodeConfirm the Setting Ex. When pressingCassette gets stuck partway Playback won’t startHDD deck Recording won’t startRemove the cassette and cover Protection switch to RECTimer again Plus+ system doesn’t work properly Re-perform the VCR Plus+ setupProcedure pg What happens if the tape runs out during recording? Can the VCR indefinitely remain in the still mode?Can the VCR indefinitely remain in the Record-Pause mode? # $ #1 and ¡ Buttons pg $S-VHS ET Button pg12ANTENNA in Connector pg REAR1VIEWDisplay Panel 8Space Button pg Cancel Button pg ControlList Of Terms 20C to 60C -4F to 140F NTSC-type colour signal and EIAMonochrome signal, 525 lines EN for Servicing Only in U.S.A Warranty Only in U.S.A EN Memo Memo HM-HDS1U

Related manuals

Manual 100 pages 29.12 Kb