JVC HM-HDS1U manual Turn on the DBS, DBS Receiver Multi-Brand Remote Control

Page 84

84 EN SPECIAL FEATURES (cont.)

	HDD	VHS	POWER
TV	1

DBS Receiver Multi-Brand Remote Control

The recorder´s remote control can control functions on the brands of DBS (Direct Broadcast Satellite) receivers listed below.

TURN ON THE DBS

RECEIVER

Turn the power on using the DBS receiver’s remote

1 control.

	2
	1	2	3
NUMBER	4	5	6
NUMBER
	7	8	9
	<	0	>
	1
	2

OK

– +

TV CH –

TV/VCR

3

4

ENTER/OK

TV CH +

	SET REMOTE CONTROL
	MODE
	Press TV on the remote control when “CABLE DBS”
	appears on the display window of the recorder’s remote
2 control.
3	ENTER DBS RECEIVER BRAND
	Enter your cable box brand code using the NUMBER
	keys, then press OK.
	Follow the example shown at bottom left.
	● Once you have set the remote control to operate the
	DBS receiver, you don´t have to repeat this step until
	you replace the remote control´s batteries.

4	OPERATE DBS RECEIVER
	First, press POWER to see if the DBS receiver’s power
	goes off as it should. If it does, try other functions (TV
	CH +/– and the NUMBER keys can be used to operate
	the DBS receiver).

	● For some brands of DBS receiver, you must press
	ENTER after having pressed the NUMBER keys.
	● To return the remote to the recorder control, press
	HDD or VHS (or S-VHS).

NOTES:

●You must set the DBS receiver brand for your remote control and the DBS receiver brand for your Controller ( pg. 19) separately.

●Depending on the type of DBS receiver, there may be cases where some or all functions cannot be operated using the remote control.

●It's not possible to operate a DBS receiver that is not equipped with a remote control sensor.

●Though ECHOSTAR has a number of different remote codes, this remote control is applicable only to one of those codes preset at the factory.

●It's not possible to set the remote control for both your DBS receiver and a cable box at the same time. You can only set the remote control to operate one of these units at a time.

DBS BRAND NAME	BRAND CODE

JVC (DISH Network)	51
ECHOSTAR (DISH Network)	51
PRIMESTAR	50
SONY (DSS)	41
RCA (DSS)	40

Image 84

Contents HM-HDS1U Dear Customer Do not place the recorderInstallation Antenna Installation Instructions USEBefore YOU Install Your NEW Recorder ServicingBefore installing the recorder Before using the recorderWhile using the recorder Contents Check Contents Power SourceConnections Situate RecorderPlug & Play Setup Plug & PlayAuto Clock Set/Auto Tuner Set Auto blinks Channel numbers are displayedAccess Main Menu Access Initial SET ScreenAccess Clock SET ClockSelect D.S.T. Mode SET Auto Clock to onSelect Host Channel Select Time ZoneSET Time SET DateSET Year ManualAccess Tuner SET Screen TunerTurn on the Recorder Set Receivable ChannelsAccess Main Menu Screen Access Tuner SET ScreenAccess Manual Channel SET Screen ADD or Skip DesiredCable Box Control Situate ControllerAttach Controller Connect Cable BOX to RecorderAccess Cable BOX SET Screen Turn on Cable BOXSelect Cable BOX Output Channel Access Cable BOX Brand SET Screen Enter Cable BOX BrandFasten securely using the supplied adhesive strips DBS Receiver ControlController DBS receiverAccess DBS Receiver SET Screen At the Initial Set UpTurn on DBS Receiver Set DBS Receiver Output Channel & DBS Receiver BrandAccess DBS Receiver SET DBS Receiver BrandSetting Blue Back Access FunctionSelect Blue Back Mode Setting Video Inputs Mode Access Video Inputs ScreenSelect Video Inputs ModeSimple Recording Simple Playback Start PlaybackPause Playback Stop PlaybackPlayback with HDD Navigation Icons and their meaningsAccess Scan Screen Select ProgramsScan for Beginnings of Programs Setting Time for Live Memory Playback Live Memory PlaybackStart Live Memory Playback About Live Memory PlaybackAccess Function Screen SuperimposeArrow to Superim Pose by pressingTo Recall Indication Playback Features Change Speed Activate Quick SkipVariable-Speed Search/ Reverse Motion Playback Quick Rewind a littleStart Rewind Repeat Playback Normal Playback OnlySelect The Soundtrack Recording Features Engage TV ModeSelect Channel for ViewingLoad a Cassette Select VHS DeckFind Program Start PointSET Tape Speed PAUSE/RESUMERecording Playback with VHS Navigation Access VHS SET UP Select VHS Navigation ModeSet VHS Navigation Tered Program Select ProgramScan for Beginning of Pro- gram with VHS Navigation Activate HIGH-SPEED Search Activate FRAME-BYChange SLOW-MOTION Speed Access Distant Code Start SearchIndex Search Tuned-in channel or AUXiliary mode Operation modeSwitchable to the tape remaining time display Press OSDTracking Mode Adjust ManualEngage Manual TrackingCounter Reset Tape Position IndicatorPress C.RESET Beginning or E End shows you Where you are on the tapeAccess VHS SET UP 1 Screen Select Picture Control ModePicture Control Access VHS SET UP Screen Select Video Stabilizer ModeVideo Stabilizer Select TBC Mode TBC byPressing Arrow to %ﬁ ∞, then press OKCalibration Mode At the top of the HDD/VHS SET UPActive Video Calibration Calibration byRecording Display Counter Information Display Tape Remaining TimeExit the Display Display Elapsed Recording TimeVHS Super VHS, S-VHS ET and VHS Engage S-VHS ET Mode Super VHS ETEngage RECORD-PAUSE Mode Locate Start PointResume Recording Stereo And SAP Second Audio Program To Record Stereo ProgramsTo Listen To Stereo Soundtrack During Recording VCR Plus+ Timer Programming Check Program Data Changing VCR Plus+ Setting Access Initial SETInitial SET UP by VCR Plus+ Guide Channel MatchingAccess Guide Channel SET Screen Input Receiving ChannelExpress Timer Programming Recorded onSET Program Date SET Program Stop TimeSET Channel Number SET Weekly or DailySET Category Check Overlap Program Return to the NormalSTOP+/-,DATE+ CH+Check, Cancel And Revise Programs VHS Deck onlyCH+ Select Auto SP=EP Timer Mode Auto SP→EP TimerTimer Recording Prepare the External Equipment for Timer RecordingEngage REC Link Mode To cancel REC Link mode, press REC Link againInstant Timer Recording ITR Engage ITR ModeSET Recording DurationAbout Hybrid Navigation About Registration of InformationAbout Editing of Programs Limitations of RegistrationAccess Modify Screen Modify InformationSelect Deck Register NEW IndexAccess Navigation Screen Enter NEW TitleRegister NEW Title Modify Program TitleSelect NEW Category Register NEW CategoryModify Category Press @%#ﬁ or 253∞ to move the arrow toAccess Delete Screen Confirm DeletionDelete Information For HDD NavigationAccess Easy Dubbing DubbingNavigation Screen Select Dubbing OptionSelect REC Speed Start DubbingNormal Dubbing DubbingEND Dubbing Press Pause on the remote control. To resume Remote controlDard at the VHS SET UP 1 of the main Menu Press VHS or S-VHS and select the program to beRandom Assemble Editing Program Editing Memory 1 program x 8 scenesSelect the Other EDIT-IN and EDIT-OUT Points Prepare VHS Deck forRecording Start EditingEdit From a CamcorderReturn to Normal Screen Start PlayerStart Recorder For HDD deckEdit To Or From Another Make ConnectionsLoad Cassettes SET RECORDER’S Input Mode Select Edit for PICStart Player Start RecorderSET Input Mode Audio DubbingEngage Audio Dubbing VHS Audio DubbingWhen monitoring the sound during Audio Dubbing, END Audio DubbingSET Remote Control TV Multi-Brand Remote ControlTurn on the TV SET TV Brand CodeCable Box Multi-Brand Remote Control Operate Cable BOXHDD or VHS or S-VHS DBS Receiver Multi-Brand Remote Control Turn on the DBSReceiver Enter DBS Receiver BrandSET Remote Control Code Enter Remote Control CodeConfirm the Setting Ex. When pressingCassette gets stuck partway Playback won’t startHDD deck Recording won’t startProtection switch to REC Timer againRemove the cassette and cover Re-perform the VCR Plus+ setup Procedure pgPlus+ system doesn’t work properly Can the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?What happens if the tape runs out during recording? # $ #1 and ¡ Buttons pg $S-VHS ET Button pg12ANTENNA in Connector pg REAR1VIEWDisplay Panel 8Space Button pg Cancel Button pg ControlList Of Terms NTSC-type colour signal and EIA Monochrome signal, 525 lines20C to 60C -4F to 140F EN for Servicing Only in U.S.A Warranty Only in U.S.A EN Memo Memo HM-HDS1U

Related manuals

Manual 100 pages 29.12 Kb