Hitachi EP-A7000 instruction manual Installation, Air Purify mode indicator is lit in green

Page 10

Installation

Install the purifier on a level, stable and sturdy surface.

Avoid any place close to cooling or heating appliance, and select a well-ventilated place.

Keep the purifier at least 90 cm away from the walls in both sides. Otherwise, discharged air will mix with surrounding air and the walls may become dirty.

WARNING

Do not place the purifier on unstable floor or pedestal.

Falling or dropping of the purifier may cause damage, failure or water leakage. Using the purifier in an inclined position may cause water leakage.

Using Remote Controller

Here we describe how to operate the air purifier using the remote controller. For the operation using the control on the purifier, please refer to page E-14.

Starting Operation

Remote Controller

Air Purifier

Indicator Section

Securely insert the power plug into AC outlet.

Press button.

Operation starts and the indicators are lit.

Pressing button during operation will stop the operation.

In the first 3 minutes after the power cord is plugged in, the unit will check room air condition and save

it in memory. During the time, the “Air Sensor” indicator and “Humidity Level 50” indicator will blink.

You may start the operation in less than 3 minutes after plugging. In this case too, the “Air Sensor” and “Humidity Level 50” indicators will continue to blink. After 3 minutes, the indicators will stop to blink and show the level of air contamination and humidity.

Blink

Blink

 

The “Air Purify” mode indicator is lit in green. *

Lit in green

Note

If On/Off button is not pressed after plugging the power cord, all indicators will go off after the “Air Sensor” and “Humidity Level 50” indicators blink for 3 minutes.

(Remote controller operation is accepted even in this state.)

E-10

Image 10
Contents EP-A7000 Features / Name of Each Component / Accessories Operation Buttons and Indicators Meanings of Symbols Safety PrecautionsDefinition of each indication Water Tank, Water Tray and Humidifying Filter To Prevent Floor Scratches or Wall Stains Do not run with filter detached Do not subject remote controller to impactDo not directly fan animals and plants Do not subject water tank to impactReinstall the panel on the unit Install the Deodorizing filterInstall the dust filter on the unit Preparations for OperationGently remove the water tank Inserting Batteries into Remote ControllerInsert batteries and close the cover Set the water tank into the water tank holderAir Purify mode indicator is lit in green InstallationRemote controller operation is accepted even in this state Pollen Installation Using Remote ControllerGreen OrangeAirflow rate changes in the following sequence Using Remote ControllerAirflow level indicator comes on Silent Medium High Blinking MaxWill continue for about 5 minutes Off-timer 4 hours is setOperation with Max airflow Operation will stop approxAir Sensor Using the Control on PurifierMemory Function Odor SensorHumidity Sensor Dust sensorAuto Detection Factory setting is Medium Each operation modeSensor sensitivity can be adjusted in 3-step fashion Press buttonIndicators are dimmed Useful FeatureEvery time you press button, Set and Cancel will alternate Cleaning When the Clean Humidifying Filter Indicator Comes OnHumidifying Filter Guide for cleaning Once a month Water Tank Guide for cleaning DailyCleaning Do not dispose of the humidifying filter case Water Tray / Tray Cover Guide for cleaning Once a monthReplacing Humidifying Filter Wipe off water and assembleRemove the panel. P.E-8 Remove the pre-filter Pre-filterGuide for cleaning Once a monthClean the pre-filter Reattach the pre-filterPurifier Body Guide for cleaning Once a month Dust sensor Cleaning guide every 3-6 monthsReplacement Interval Filter ReplacementPrecautions on Filter Handling Use a genuine filter for the Hitachi Air Purifier Replacing the FilterRemove the panel and the pre-filter Remove the used filter It may also be a cause of malfunctionTroubleshooting Guide Alert DisplayClean Humidifying Filter indicator does not go off Water leaks Indicator is dimIs there anything nearby that the odor sensor might sense? Following Conditions Are Normal Deodorizing filter 10kg Length of power cord Approx .8mApplicable floor space 50m