Hitachi EP-A7000 instruction manual Cleaning, When the Clean Humidifying Filter Indicator Comes On

Page 18
P.E-9

Cleaning

Before cleaning, be sure to stop operation and unplug the power cord from AC outlet.

WARNING

CAUTION

Do not splash water on the purifier body. Water splash can be a cause of failure.

Do not use a volatile solvent, such as gasoline, thinner, benzene, wax, kerosene, alcohol, etc. or polishing powder, or detergent (neither kitchen nor laundry use).

Such chemicals could cause deformation, discoloration, damage or removal of prints. Do not tilt or tip over the unit.

When using a chemically treated cloth, follow its instructions.

Never use dryer or heater to dry the purifier case. Heating could cause deformation, discoloration, damage or removal of prints.

Lay a soft cloth or the like beneath the purifier to protect the floor against scratch.

When the “Clean Humidifying Filter” indicator is lit, clean the humidifying filter, water tray and tray cover. The “Clean Humidifying Filter” indicator will come on approx. one month (approx. 720 hours) after the start of use or after the reset button was pressed upon finishing previous cleaning. Depending on the tap water used, water scale may adhere earlier. If the filter contamination is heavy, clean the filter more than once a month before the “Clean Humidifying Filter” indicator is lit.

When you are done with cleaning, press the reset button. The “Clean Humidifying Filter” indicator will go off.

When the “Clean Humidifying Filter” Indicator Comes On

Remove the water tank, and then pull out the water tray.

Water tray

Slowly pull out the water tray while lifting it obliquely upward.

Remove the humidifying filter from the water tray.

Humidifying filter

Water tray

手前

CAUTION

When you pull out the water tray, water may spill out or the floor may be scratched with bottom of the tray. Lay a soft cloth or the like beneath the purifier to protect the floor.

Clean the humidifying filter, water tray and tray cover.

P.E-19, E-20

When the purifier body is shaken or rocked, water may gather in other part of the water tray not to be fitted with the humidifying filter.

After you pulled out the water tray, be sure to remove the tray cover and wipe off water or clean it.

Set the humidifying filter.

Slowly insert the humidifying filter into the tray cover. Insert the filter fully until it comes into positive contact with bottom of the tray. Inadequate fitting may cause water leakage during operation.

手前

Marking

Humidifying filter

手前

Install the water tray, and then

Remove the panel.

P.E-8

mount the water tank.

 

 

Plug the power cord in AC outlet

Reset button “Clean” indicator (Red)

and press the reset button located

 

 

behind the panel.

 

 

Press the reset button located behind the panel. (Use the tip of a ball-point pen or the like.) Check that the “Clean” indicator is now OFF.

Mount the panel on the unit.

P.E-8

E-18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents EP-A7000 Features / Name of Each Component / Accessories Operation Buttons and Indicators Safety Precautions Meanings of SymbolsDefinition of each indication Water Tank, Water Tray and Humidifying Filter To Prevent Floor Scratches or Wall Stains Do not run with filter detached Do not subject remote controller to impactDo not directly fan animals and plants Do not subject water tank to impactReinstall the panel on the unit Install the Deodorizing filterInstall the dust filter on the unit Preparations for OperationGently remove the water tank Inserting Batteries into Remote ControllerInsert batteries and close the cover Set the water tank into the water tank holderInstallation Air Purify mode indicator is lit in greenRemote controller operation is accepted even in this state Pollen Installation Using Remote ControllerGreen OrangeAirflow rate changes in the following sequence Using Remote ControllerAirflow level indicator comes on Silent Medium High Blinking MaxWill continue for about 5 minutes Off-timer 4 hours is setOperation with Max airflow Operation will stop approxAir Sensor Using the Control on PurifierMemory Function Odor SensorDust sensor Humidity SensorAuto Detection Factory setting is Medium Each operation modeSensor sensitivity can be adjusted in 3-step fashion Press buttonUseful Feature Indicators are dimmedEvery time you press button, Set and Cancel will alternate Cleaning When the Clean Humidifying Filter Indicator Comes OnWater Tank Guide for cleaning Daily Humidifying Filter Guide for cleaning Once a monthCleaning Do not dispose of the humidifying filter case Water Tray / Tray Cover Guide for cleaning Once a monthReplacing Humidifying Filter Wipe off water and assembleRemove the panel. P.E-8 Remove the pre-filter Pre-filterGuide for cleaning Once a monthClean the pre-filter Reattach the pre-filterPurifier Body Guide for cleaning Once a month Dust sensor Cleaning guide every 3-6 monthsFilter Replacement Replacement IntervalPrecautions on Filter Handling Use a genuine filter for the Hitachi Air Purifier Replacing the FilterRemove the panel and the pre-filter Remove the used filter It may also be a cause of malfunctionTroubleshooting Guide Alert DisplayWater leaks Indicator is dim Clean Humidifying Filter indicator does not go offIs there anything nearby that the odor sensor might sense? Following Conditions Are Normal 10kg Length of power cord Approx .8m Deodorizing filterApplicable floor space 50m
Top Page Image Contents