EAW DSA250i, DSA230i owner manual Lift the enclosure onto the structure-mounted Wall Brackets

Page 30

USER SUPPLIED

ATTACHMENT

HARDWARE

Ø 0.39 in Ø 9.9 mm

Figure 5.6.7d Wall Bracket Attachment (For illustration purpose only. Attachment hardware selection is installer’s responsibility.)

4.Provide attachment hardware and secure the supplied Wall Brackets to the mounting structure, complying with all Danger and Caution notes in Section 5.6.1.

NOTE: The Wall Brackets have a weld nut on one side. Be sure to locate this weld nut to the right or left such that the Retainer Bolt can be inserted into the opposite side of the Wall Bracket after the module is mounted.

2X ENCLOSURE MOUNTING BRACKET P/N 0006118

2X 3/8-16 X 2 LG HEX HEAD SCREWS & LOCK WASHERS

Figure 5.6.8 Enclosure Bracket Installation

5.6.8 ENCLOSURE BRACKET INSTALLATION

Insert each supplied Enclosure Bracket into its slot near each end of the enclosure, verifying the proper orientation of the enclosure. Insert a supplied 3/8-16 x 2 in Enclosure Bracket Bolt with its lock washer into each bracket bolt hole in the enclosure. Thread each bolt into the weld nut on its Enclosure Bracket and hand-tighten.

Caution: Make sure the brackets are installed so the enclosure orientation will be correct when the enclosure is mounted.

5.6.9 ENCLOSURE INSTALLATION

1. Lift the enclosure onto the structure-mounted Wall Brackets

DANGER: IT IS RECOMMENDED

THAT LIFTING THE ENCLOSURE IN

PLACE BE PERFORMED BYAT LEAST

TWO PEOPLE TO PREVENT IT FROM

FALLING DURING ITS INSTALLATION

2X WALL AND CAUSING POSSIBLE EQUIP-

MOUNTING

BRACKET MENT DAMAGE, INJURY, OR DEATH.

P/N 0006119

CAUTION: For DSAi Clusters with two or more modules mounted one over the other, it is recommended to make all cable connections before lifting the mod- ules onto the wall brackets. See Sections

5.2through 5.5. Once the modules are mounted, access to the connectors may be difficult.

IMPORTANT: When installing modules mounted vertically end to end, install the lower module first.

Figure 5.6.9a Enclosure Installation

26

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Page Safety Precautions Read this First Precauciones DE Seguridad LEA Esto Primero EC Declaration of Conformity Contents Page Unpacking ContentsIntroduction Shipping DamageReturning Products to EAW Audio Signal ConnectionChapter Quick StartDaisy Chaining Audio and Computer Signal Between Modules AC Mains InstallationComputer Control Connection Physical Installation Signal End / Power EndSignal Processing DescriptionSystem Overview Features 4 DSAi Block DiagramsElectronic Applications Engineering Design4a Angled Radiation Pattern Comparison to Traditional Products DSAPilotLow Frequency Performance Designing DSAi SystemsInstallation Analog Audio and EIA-485 Computer Control2 Audio a & Audio B Recommended Conductor Gauge AWG to 18 AWG / 0.2 mm to 1 mm 3 Basic CobraNet Diagram CobraNet Audio and Computer ControlCabling Fault Detect Supervisory Monitoring 3a Single DSAi Fault on AC Mains Power Connection 2 PowerCon PlugGrounding 4 Fuse2 Signal End / Power End 3 DSAi Cluster Configurations 4a Wall Mounted 6 Mounting Height Lift the enclosure onto the structure-mounted Wall Brackets Acoustical Installation Initial Set-UpOperation Operational FunctionsSignal Monitoring Operational Check List Normal OperationOperational ‘DOS’ and ‘DONTS’ Service Items Maintenance and ServiceWarranty How to Contact EAWInspections and Maintenance AppendicesTroubleshooting DSA250i OnlyEIA-485 EIA-485 Network Notes CobraNetSupport For Ethernet Support For CobraNetDSAi Connections 3a EIA-485 Example 5c Example One path was to the EIA-485 port. So when B responds 6c Example Mechanical Drawings Right Side BackRight Side Full Scale Wall Bracket
Top Page Image Contents