Lincoln Electric SVM189-B service manual Procedure, Figure F.1 Case Removal

Page 66

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

F-12	TROUBLESHOOTING & REPAIR	F-12

CASE COVER REMOVAL AND REPLACEMENT PROCEDURE (CONTINUED)

FIGURE F.1 – CASE REMOVAL

2 Phillips Screws

on Models with

Metal Handle

3/4”	5/16 Hex Head Screws
Screws
(2 Places)

5/16 Hex Head on Models with Plastic Handle

LINCOLN

ELECTRIC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

PROCEDURE

1.Disconnect power to the machine.

2.Remove the two(2) 5/16 hex-head screws from the top of the door and remove the door

3.Remove the ten(10) hex-head screws from the top and left side of the machine. Note the position of the two(2) longer screws. See Figure F.1

NOTE: If the machine has a plastic handle, remove the 5/16 hex-head screw from the front and remove the handle.

4.Carefully lift and remove case cover from the machine.

NOTE: Depending on what needs to be done, it may be desirable to remove the handle on machines with the metal handle. See Figure F.1

COMPACT WIRE WELDERS

Image 66

Contents Safety Depends on You SVM189-BSafety California Proposition 65 WarningsElectric Shock can kill ARC Rays can burn Welding Cutting For ElectricallyIii Précautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical SpecificationsStacking Safety PrecautionsSelect Suitable Location TiltingIdentify and Locate Components Table of Contents Operation Section Common Welding Abbreviations OperationProduct Description Product Capabilities Wear eye, ear and body protec- tionControls and Settings See Figure B.1See Figure B.2 See Figure B.3 Drive Roll Tension Thumbscrew TurningWire Diameter Drive Roll Drive Roll Part Inner Wire Guide Number Part NumberSetting UP and Making a FLUX-CORED Weld Items Needed for Flux Cored WeldingLoad Wire Spool Connect Leads and Cables onMachine Figure B.9 MIG Conversion Kit K2526-1 025Install Shielding GAS Shielding GAS11OPERATION Connect Leads and Cables on the Machine12OPERATION Do not Remove or Conceal Warning LabelsFigure B.20 Compact Wire Welders Table of Contents Accessories Section K2532-1 Magnum 100SG Spool Gun AccessoriesK2525-1 Spot Timer Kit K2377-1 Small Canvas CoverK520-Utility Cart K2275-1 Welding Cart Technical Specifications Magnum 100SG Spool GUN K2532-1 Unpacking the Spool GUNSafety Precautions Locating Spool GUN Components FeaturesAssembly of Items Inside the Magnum Spool GUN Figure C.3Safety Precautions Welding Machines Recommended Welding MachinesSpool GUN Spool GUN / Wire Drive Selector Switch Installation Disconnect input power from the machineOpen the Machine Electrical Connections 11.B. Connect P5 6-pin to harness J8 6-pin11.C. Connect harness P8 6-pin to board J5 6- pin If Machine does have Optional Spot Timer .A. thru 12.D 544A 543AMounting the Switch RE-ASSEMBLE Machine AS FollowsRoutine Welding Machine Preparation ACCESSORIESC-13Disconnect input power to the machine Preparing the Spool GUNLoading Aluminum Wire Figure C.5Figure C.11 Connecting the GUN to the Welding Machine Figure C.17Table of Contents Maintenance Section Maintenance Maintenance Safety PrecautionsRoutine Maintenance GUN and Cable Maintenance Overload ProtectionFor Magnum 100L GUN Changing Liner GUN Handle PartsLiner trim length Major Component Locations Maintenance 1TABLE of CONTENTS-THEORY of Operation Section E-1 Theory of Operation General DescriptionFigure E.3 Input Power Circuits Input Line VOLTAGE, FAN Motor & Main TransformerOutput CONTROL, Rectification & Voltage Feedback Figure E.4 Output CircuitsTRIGGER, GAS Solenoid and Wire Drive Figure E.5 TRIGGER, GAS Solenoid & Wire DriveSCR Operation Figure E.6 SCR OperationElectronic Wire Drive Motor Protection Compact Wire Welders Table of Contents Troubleshooting & Repair Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures Wiring Diagram OUTPUT/FEEDING Problems Feeding Problems Welding Problems Maintenance Section Issues Maintenance Section Cone or gas diffuser Case Cover Removal and Replacement Procedure Test DescriptionMaterials Needed Procedure Figure F.1 Case RemovalGAS Solenoid Test GasSolenoid Leads Wire Drive Motor Test Test Procedure MOT-MOT+Main Transformer Test Secondary Test Procedure Secondary Lead Compact Wire Welders FAN Motor Test Figure F.5. Control Board Lead Locations Scope Settings Typical Output Voltage Waveform Machine LoadedVolts 10Volts 20ms Abnormal Open Circuit Voltage Waveform Control Board Removal and Replacement Procedure See Figure F.7 Nameplate Control Knob Compact Wire Welders Power Module Removal and Replacement Procedure Viewed from Rear of Machine Center Panel PolarityPanel CenterPanelScrews OutputStuds Compact Wire Welders Misc. Hand Tools Dow Corning Fine Steel Wool See Figure F.12 Dow Corning Figure F.12 DOW Corning Application Areas Transformer Compact Wire Welders Wire Drive Motor Removal and Replacement Procedure Lincolnelectric Phillips Mounting Screws Compact Wire Welders FAN Motor Assembly Removal and Replacement Procedure Viewed from Rear of Machine Center Panel CenterPanelScrews Locking Tabs Fan Retest After Repair 140 AMP Units Troubleshooting & Repair Retest After Repair 125 AMP UnitsWire Speed Range Open Circuit VoltageTroubleshooting & Repair Retest After Repair 180 AMP Units Table of Contents Diagram Section Wiring Diagram COmpacT WirE WElDErSSpool GUN Interface Wiring Diagram Wiring Diagram M20410-3 a COmpacT WirE WElDErS Thermostat TMP FAN TS1SchEmaTic cOmplETE machiNE m21240 C12 R1Feed R24