Lincoln Electric FX450 specifications Gtaw, Cv-Gas, Weld Terminals On/Remote

Page 20

b-7

OPERATION

b-7

 

 

 

GTAW

This weld mode is a constant current (CC) mode featuring con- tinuous control from 10 – 500 amps. It is intended for the GTAW TIG welding processes.

hot Start - The Hot Start control regulates the starting current at arc initiation. Hot Start can be set to “Off” and no additional current is added at arc start. When set to the “On” position, additional current (relative to the preset current) at arc initiation.

Arc Control – This control is not used in the GTAW mode.

Weld Terminals On/Remote

•When set to the “ON” position, the weld terminals are at OCV (open circuit voltage) and ready to weld.

•When set to the “REMOTE” position, output is enabled through a remote trigger.

Voltage Display Meter – This display will display three dashed lines when the machine is in the idle state. This indicates that voltage is not settable in this weld mode. While output is enabled, the actual welding voltage is displayed. After welding, the meter holds the actual voltage value for 5 seconds. Output adjustment while in the "hold" period results in the "prior to operation" characteristics. The displays blink indicating that the machine is in the "hold" period.

Amperage Display Meter – This display will display the pre-set welding current when the machine is in the idle state. While output is enabled, the actual weld amperage is displayed. After welding, the meter holds the actual amperage value for 5 sec- onds. Output adjustment while in the "hold" period results in the "prior to operation" characteristics. The displays blink indicating that the machine is in the "hold" period.

Output Control Local/Remote – When the control is set to local (no remote potentiometer/control plugged into the 6-pin or 14-pin connectors), the output is controlled through the Output Control Dial on the front of the FX450. Set this switch to “REMOTE” when an external potentiometer/control is connect- ed.

•When a remote potentiometer is connected, the output control on the FX450 and the remote act as a master/slave configura- tion. Use the control dial on the FX450 to pre-set the maxi- mum welding current. The remote will control output from minimum to the pre-set maximum.

Output Control Dial

•When the Local/Remote is set to Local, this dial sets the welding amperage.

•When the Local/Remote is set to Remote, this dial sets the maximum welding amperage.

The remote potentiometer controls the amperage from minimum to this pre-set maximum.

CV-GAS

This weld mode is a constant voltage (CV) mode featuring con- tinuous control from 10 to 45 volts.

It is intended for the GMAW, FCAW-GS, MCAW welding processes and arc gouging.

hot Start – Toggle to “ON” position to provide more energy during the start of a weld.

Arc Control – The Arc Control regulates pinch effect (Inductance). At the minimum setting (-10), minimizes pinch and results in a soft arc. Low pinch settings are preferable for weld- ing with gas mixes containing mostly inert gases. At the maxi- mum setting (+10), maximizes pinch effect and results in a crisp arc. High pinch settings are preferable for welding FCAW-GS and GMAW with CO2.

Weld Terminals On/Remote

•When set to the “ON” position, the weld terminals are at OCV (open circuit voltage) and ready to weld. This selection is used for across the arc wire feeders.

•When set to the “REMOTE” position, output is enabled through a remote trigger.

Amperage Display Meter – This display will display three dashed lines when the machine is in the idle state. This indi- cates that amperage is not settable in this weld mode. While output is enabled, the actual welding amperage is displayed. After welding, the meter holds the actual amperage value for 5 seconds. Output adjustment while in the "hold" period results in the "prior to operation" characteristics. The displays blink indi- cating that the machine is in the "hold" period.

Voltage Display Meter – This display will display the pre-set welding voltage when the machine is in the idle state. While out- put is enabled, the actual weld amperage is displayed. After welding, the meter holds the actual voltage value for 5 seconds. Output adjustment while in the "hold" period results in the "prior to operation" characteristics. The displays blink indicating that the machine is in the "hold" period.

Output Control Local/Remote – When the control is set to local (no remote potentiometer/control plugged into the 6-pin or 14-pin connectors), the output is controlled through the Output Control Dial on the front of the FX450. Set this switch to “REMOTE” when an external potentiometer/control is connect- ed.

Output Control Dial

•When the Local/Remote is set to Local, this dial sets the welding voltage.

•When the Local/Remote is set to Remote, this dial is disabled.

FX450 (RED-D-ARC)

Page 19 Page 21
Image 20
Page 19 Page 21
Contents RED-D-ARC Safety California Proposition 65 WarningsElectric Shock can kill ARC Rays can burnIii Welding and Cutting Sparks can Cause fire or explosionCylinder may explode if damaged PRÉCAuTIONS DE Sûreté Sûreté Pour Soudage a L’ArcPlease Examine Carton and Equipment For Damage Immediately CuSTOMER Assistance PolicyTAbLE of Contents Installation TEChNICAL Specifications FX450Voltage FX450 RED-D-ARCProcess ModelEnvironmental Limitations LiftingStacking INPuT Voltage Selection INPuT FuSE and SuPPLY Wire ConsiderationsINPuT Connection PIN Remote Control Connector Function Pin WiringPIN Connector for Wire Feeder CAbLE ConnectionsRecommended Electrode and Work CAbLE SIzES for ARC Welding Control CAbLE ConnectionsGeneral Guidelines TAbLE A.1 OuTPuT CAbLE GuIDELINESSafety PRECAuTIONS Wire FeederOperation OFFProtective PRODuCT DescriptionVoltage EQuIPMENT EQuIPMENT LimitationsRecommended Processes Process LimitationsCase Front Control Descriptions FIGuRE b.1Common Welding PROCEDuRES Input Power Cord Access holeCase bACK Control Weld Controls and DisplaysWeld Terminals On/Remote Toggle Switch Control Local/Remote Toggle SwitchBASIC Modes of Operation Thermal LightWeld Terminals On/Remote GtawCV-GAS CV-INNERShIELD Accessories Options / AccessoriesGeneral Options TIG OptionsMaintenance ROuTINE MaintenancePERIODIC MAINTENANCE Thermal ProtectionTROubLEShOOTING HOW to uSE TROubLEShOOTING GuIDEPRObLEMS SymptomsPOSSIbLE CAuSE RecommendedUSING ThE STATuS LED to TROubLEShOOT System PRObLEMS Error Codes for the FX450Diagrams FX450 RED-D-ARCDimension Print Precaucion Warnung
Top Page Image Contents