Lincoln Electric IM810 manual Changing Liner, GUN Handle Parts, Liner trim length

Page 26

D-4

MAINTENANCE

D-4

Set Screw

Brass Cable

 

 

 

 

 

 

Connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Liner Assembly

(Liner bushing to be sealed tight against brass cable connector)

1-1/4 (31.8 mm) Liner Trim Length

Gas Diffuser

Gas Nozzle or Gasless Nozzle

FIGURE D.2

Liner trim length

CHANGING LINER

NOTICE: The variation in cable lengths prevents the interchangeability of liners. Once a liner has been cut for a particular gun, it should not be installed in anoth- er gun unless it can meet the liner cutoff length requirement. Refer to Figure D.2.

1.Remove the gas nozzle from the gun by unscrew- ing counter-clockwise.

2.Remove the existing contact tip from the gun by unscrewing counter-clockwise.

3.Remove the gas diffuser from the gun tube by unscrewing counter-clockwise.

4.Lay the gun and cable out straight on a flat surface. Loosen the set screw located in the brass connec- tor at the wire feeder end of the cable. Pull the liner out of the cable.

5.Insert a new untrimmed liner into the connector end of the cable. Be sure the liner bushing is stenciled appropriately for the wire size being used.

6.Fully seat the liner bushing into the connector. Tighten the set screw on the brass cable connector. At this time, the gas diffuser should not be installed onto the end of the gun tube.

7.With the gas nozzle and diffuser removed from the gun tube, be sure the cable is straight, and then trim the liner to the length shown in the Figure D.2. Remove any burrs from the end of the liner.

8.Screw the gas diffuser onto the end of the gun tube and securely tighten.

9.Replace the contact tip and nozzle.

GUN HANDLE PARTS

The gun handle consists of two halves that are held together with a collar on each end. To open up the handle, turn the collars approximately 60 degrees counter-clockwise until the collar reaches a stop. Then pull the collar off the gun handle. If the collars are diffi- cult to turn, position the gun handle against a corner, place a screwdriver against the tab on the collar and give the screwdriver a sharp blow to turn the collar past an internal locking rib. See Figure D-3.

Figure D-3

Counter-clockwise

Pro-MIG 175

Image 26
Contents Pro-MIG Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcPlease Examine Carton and Equipment For Damage Immediately On-Line Product RegistrationTable of Contents Installation Safety Precautions Identify and Locate ComponentsOutput Connections Work Clamp InstallationSelect Suitable Location StackingConnecting Gun Cable to the Pro-MIG GUN InstallationWork Cable Installation Input Connections Figure A.5Volt Input Connection Line Cord ConnectionElectrical Input Connection for Rated Output Operation Saftey PrecautionsDesign Features Advantages General DescriptionLimitations Controls and SettingsWelding Capability Welding Operations Wire LoadingFriction Brake Adjustment Sequence of OperationWire Threading Refer to Figure B.4 Over the drive roll 3, and into the outgoingMaking a Weld Cleaning Tip And NozzleProcess Guidelines Overload Protection Changing Machine Over to Feed Other Wire SizesWelding with Gmaw MIG Application Chart K586-1 Deluxe Adjustable Gas Regulator & Hose Kit AccessoriesOptional Accessories K549-1 .035 0.9 mm Innershield Welding KitInnershield Fcaw Conversion Replacement Parts025 .035 0.6 0.9mm wire Routine Maintenance MaintenanceMaintenance Safety Precautions For Magnum 100L GUN GUN and Cable MaintenanceConfiguration of Components in Wire Feeding System Contact Tip Cable Liner Drive RollComponent Replacement Procedures Changing the Contact TIPLiner trim length Changing LinerGUN Handle Parts Troubleshooting HOW to USE Troubleshooting GuideProblems Possible Symptoms Cause Recommended Course of ActionGAS Flow Problems Welding Problems Pro-MIG 175 Wiring Diagram Page Page Precaucion Warnung

IM810 specifications

The Lincoln Electric IM810 is a highly regarded industrial inverter-based welding machine that offers unparalleled performance and versatility for a variety of welding applications. Known for its robust design and advanced technology, the IM810 is ideal for professionals in industries such as construction, shipbuilding, and manufacturing.

One of the standout features of the IM810 is its advanced inverter technology, which provides a significant reduction in weight and size compared to traditional welding machines. This makes the unit highly portable and easy to handle in different working environments. Despite its compact design, the IM810 does not compromise on power, delivering impressive output capabilities to tackle even the most demanding welding tasks.

The IM810 supports a range of welding processes, including MIG, TIG, and stick welding. This versatility allows users to switch between different types of welding applications with ease, making it a valuable tool for technicians who need to adapt to various projects. Moreover, its dual voltage capability enables operation on both 120V and 230V power supply, increasing its usability in different settings.

Another key feature is the machine’s user-friendly interface. The IM810 is equipped with an intuitive digital display that makes it easy for users to monitor settings and adjust parameters on the fly. This helps to streamline the welding process and improve efficiency. Additionally, the machine includes a range of pre-set programs for different materials and thicknesses, enabling users to achieve optimal results with minimal setup time.

The IM810 is also designed with durability in mind. Constructed from high-quality materials, it can withstand the rigors of industrial environments. Its heavy-duty construction ensures long-lasting performance, while built-in thermal overload protection safeguards the machine against overheating, extending its lifespan.

With a focus on safety, the IM810 incorporates various features to protect both the operator and the equipment. These include a sturdy roll cage for physical protection and advanced cooling systems that maintain optimal operating temperatures.

In summary, the Lincoln Electric IM810 is a versatile, powerful, and durable welding machine that combines advanced technology with user-friendly features. Its ability to handle multiple welding processes, coupled with its portability and safety features, makes it an essential tool for professionals who demand quality and reliability on the job.