Lincoln Electric IM767 specifications Changing the Contact TIP, Changing Drive Roll

Page 37

D-3

MAINTENANCE

 

 

 

D-3

COMPONENT REPLACEMENT PROCEDURES

CHANGING THE CONTACT TIP

1.Unplug or turn power switch to Off “O” position.

2.Refer to Figure D.2. Remove the gas nozzle from the gun by unscrewing counter-clockwise.

3.Remove the existing contact tip from the gun by unscrewing counter-clockwise.

4.Insert and hand tighten desired contact tip.

5.Replace gas nozzle.

CHANGING THE WELDMARK 135 PLUS FOR USE WITH INNERSHIELD FLUX CORED WIRE

•Change The Contact Tip

1.Refer to Figure D.2. Remove the gas nozzle from the gun by unscrewing counter-clockwise.

2.Remove the existing contact tip from the gun by unscrewing counter-clockwise.

3.Insert and hand tighten the contact tip for use with 0.035” Innershield Flux Cored Wire.

4.Replace gas nozzle – The gasless nozzle may be used instead of the gas nozzle to give improved visibility of the arc.

CHANGING DRIVE ROLL

The drive roll, Figure D.1 Item 1, has two grooves; one for .023" – .025" (0.6 mm) solid steel electrode and a larger groove for .030" (0.8 mm) solid and .035" (0.9 mm) flux-cored steel electrode. As shipped, the drive roll is installed in the .023"-.025" (0.6 mm) position.

If .030"/.035" (0.8/0.9 mm) wire is to be used, the drive roll must be reversed as follows:

1.Turn the power switch to OFF (marked “O”).

2.Release the spring-loaded idle arm tensioner, Figure D.1 Item 2, and lift the idle roll arm, Figure D.1 Item 3, away from the drive roll.

3.Loosen the Phillips Head screw holding the drive roll onto the drive shaft.

CAUTION

When inching the welding wire, the drive rolls, gun connector block, and gun contact tip are energized relative to work and ground and remain energized for several seconds after the gun trig- ger is released.

4.Remove the drive roll, flip over and reinstall with the opposite groove closest to the gearbox.

NOTE: The stencil of the groove that you want to use is marked on the outside of the drive unit (when installed)

5.Push a length of straightened welding wire through the wire feeder guide tubes and reset the Phillips Head screw to secure the drive roll onto the shaft.

6.Reapply the spring loaded idle arm tensioner.

7.Turn the power “ON” (I) and check the drive roll for slipping when feeding wire. DO NOT OVERTIGHTEN - If necessary, tighten or loosen the spring loaded idle arm tensioner (2).

3

2

1

FIGURE D.1

WELDMARK 135 PLUS

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Weldmark 135 Plus California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéOn-Line Product Registration Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Technical Specifications Weldmark 135 Plus InstallationIdentify and Locate Components Safety PrecautionsElectric Shock can kill Work Cable Installation Work Clamp InstallationSelect Suitable Location StackingConnecting Gun Cable to the Weldmark 135 Plus GUN InstallationGAS Connection Gas Solenoid Inlet Fitting Input ConnectionsInput CableRequirements For Rated Output Code Requirements for Input ConnectionsRequirements For Maximum Output Operation Observe all safety information throughout this manualFumes and Gases can be dangerous Welding Sparks can cause fire or explosionDesign Features Advantages Controls and SettingsGeneral Description Welding CapabilityWelding Operations Wire LoadingSequence of Operation Wire Threading Friction Brake Adjustment4OPERATIONB-4 Making a Weld Shielding GasCleaning Tip And Nozzle Changing Machine Over to Feed Other Wire SizesProcess Guidelines Overload Protection Wire Feed Overload ProtectionOutput Overload Thermal ProtectionLearning to Weld Learning to WeldARC-WELDING Circuit SELF-SHIELDED Fcaw Welding ARCProcess Selection Gmaw MIG Welding ARCJoint Types and Positions Common MetalsFor Gmaw MIG Process For Fcaw Innershield ProcessPenetration Welding In The Vertical PositionFillet Welds Welding Techniques for the SELF- Shielded Fcaw Process Machine SET UP for the SELF-SHIELDED Fcaw ProcessVertical-down Welding Correct Welding PositionCorrect Welding Speed Correct Electrical Stickout ESOPractice Helpful HintsWelding Techniques for the Gmaw MIG Process Machine SET UP for the Gmaw MIG ProcessFor the Weldmark 135 PLUS, use Following To Eliminate a Ropy Convex Bead in order of importance Troubleshooting WeldsTo Correct Poor Penetration in order of impor- tance To Eliminate Stubbing* in order of importanceProper Gun Handling Application Chart Optional Accessories AccessoriesK586-1 Deluxe Adjustable Gas Regulator Hose Kit Innershield Fcaw Conversion Replacement PartsMaintenance Safety Precautions MaintenanceItems Requiring no Maintenance Routine and Periodic MAINTE- NanceConfiguration of Components in Wire Feeding System GUN and Cable MaintenanceFor Magnum 100L GUN Contact Tip Cable Liner Drive RollChanging Drive Roll Changing the Contact TIPGUN Handle Parts Changing LinerLiner trim length for gun with red trigger Magnum 100L HOW to USE Troubleshooting Guide TroubleshootingOutput Problems Troubleshooting GuideRecommended Course of Action Problems Possible Symptoms CauseGAS Flow Problems SP-135PLUSWIRINGWIRINGDIAGRAMDIAGRAMS Wiring DiagramsWeldmark 135 Plus Precaucion Warnung Manufactured by Lincoln Electric Company
Top Page Image Contents