Lincoln Electric V205-T service manual Controls and Settings, Figure B.2

Page 18

to Section TOC

to Master TOC

B-4		OPERATION	B-4

CONTROLS AND SETTINGS

All operator controls and adjustments are located on the case front of the V205-T machine. Refer to Figure B.2 and the corresponding explanations.

FIGURE B.2

Return

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return

Return to Master TOC

Return to Master TOC

Return to Master TOC

9 87

LOCAL

sec

sec

13

1

2

3

1011

1.Input Voltage warning light green LED - Indicates that the machine is on and input voltage is within acceptable range.

2.Thermal Shutdown Light (yellow LED) - Indicates thermal over load or output disabled for incorrect supply voltage.

•With the "Yellow LED" on, and an alarm code blink- ing on "Digital Display Item 6" (see Troubleshooting Section E, "Possible electrical problems"), the machine will not supply power at the output.

•If over-heating occurs, the "Yellow LED" will stay on until the machine has sufficiently cooled. Leave the power source on to allow the fan to cool the unit.

3.Pulse On/OFF push button - CONSTANT current - PULSED current

6

1. Input Voltage warning Light Green LED

2. Thermal / Device Warning Light Yellow LED

3. Pulse On/Off Button

4. Setup/Parameter Select Button

55. Output/Parameter Adjust Knob

6. Digital Display

7.Local/Remote Button

8.Trigger Selection Button

9. Welding Process (MODE) Button

410. Electrode Connection (Negative)

11.Remote Control Connector

12.Electrode Connection (Positive)

13. Welding Parameter Drawing

12

4.Setup/Parameter Select push button - “Setup/Parameter" push button has three (3) differ- ent functions:

•Accesses Welding Parameter. Repeatedly pressing the Parameter button will step through the Welding Parameter waveform lights on the front panel. Parameters which can be changed.

Start Current

Upslope

Weld Current (Peak Current)

Pulse Frequency

%on Time Background Current Downslope Finish Current Postflow sec.

There is a LED for each welding parameter. When lit, it has confirmed the mode or selection chosen.

•Accesses the "AC Frequency" and "AC Balance" by pressing and holding the Parameter button for three (3) seconds.

•Accesses the "Set Up Menu". See Set Up Menu section.

V205-T AC/DC

Image 18

Contents Invertec V205-T AC/DC Safety Electric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation Section Installation Operating Temperature Range Storage Temperature RangeTilting Select Suitable LocationStacking Environmental AreaReconnect Procedure Input Connections115V Input Attachment Plug Installation230V Input Engine Driven GeneratorOutput Connection for Stick Output and GAS Connection for TIG Welding Figure A.1Work Cable Connection Remote Control Connection Shielding GAS ConnectionV205-T AC/DC Table of Contents Operation Section Welding Capability Safety InstructionsGeneral Description LimitationsRear Control Panel Figure B.1 Figure B.1Controls and Settings Figure B.2Step Diagram Local/Remote push button Selects the weldingTIG DC TIG AC SET UP Menu Indicator Parameter DefaultOutput Limitations Welding PolarityFigure B.5 Tips for AC TIG Welding Steel TIG WeldingCopper TIG Welding Filler MaterialAC TIG Welding Quick Start UP Protective GASDC TIG Welding Quick Start UP Table of Contents AccessoriesCable Plugs Optional AccessoriesCompatible Equipment TIG Torch KitsTable of Contents Maintenance Safety Precautions Input Filter Capacitor Discharge ProcedureRoutine Maintenance Table of Contents Theory of Operation Section Theory of Operation General DescriptionInput Board and BUS Board Main Igbt Inverter Board Figure E.3 Main Igbt Inverter BoardOutput Module and Clamping Board Main TransformerOutput Module Transistor Board Superimposition BoardCONTROL/DISPLAY Board High Frequency HF Board Output Filter BoardInsulated Gate Bipolar Transistor Igbt Operation Figure E.6 IgbtTable of Contents Troubleshooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures Electric Shock can killOutput Problems Function Problems Function Problems Secondary Power Board Test Welding Problems Troubleshooting & Repair External Diagnostics Figure F.1 External DiagnosticsTroubleshooting & Repair Internal Diagnostics Figure F.2Internal Diagnostics LEDV205-T AC/DC Input Filter Capacitor Discharge Procedure DescriptionInput Filter Capacitor Discharge Procedure Discharge ProcedureInput Filter Board Test Input Filter Board Figure F.5 Input Filter Board V205-T AC/DC Main Igbt Inverter Board LOW Voltage Test Main Board LED Table F.1 Test PointsTP2 MF2 Figure F.7 Main Igbt Inverter Board LocationCONTROL/DISPLAY Board Test Control/Display Board CN2 CN7 CN1 Figure F.9 CONTROL/DISPLAY Board LocationTable F.3 Plug CN2 Test Points CN1Table F.2 Plug CN1 Test Points Table F.4 Plug CN7 Test PointsBUS Board Test BUS Board Table F.7 Plug CN4 Test Points Table F.5 Plug CN2 Test PointsTable F.6 Plug CN3 Test Points Table F.8 Plug CN7 Test PointsCN2 CN4Main Inverter Board Upfr Section Test Figure F.14 Upfr Location on Main Board Table F.10 Voltage Checks with 115 VAC Applied to MachineTP9 Gndpwr RL1 DD1 MF9V205-T AC/DC Troubleshooting and Repair Output Filter Board TestOutput Filter Board Figure F.17 Output Filter Board Plug Location Figure F.18 Output Filter Board Plug CN1V205-T AC/DC Secondary Power Board Test Secondary Power Board Figure F.20 Secondary Power Board Test Point Locations Table F.13 Voltage Checks with 115 VAC Applied to MachineV205-T AC/DC Main Inverter Board Welding Logic and Inverter Section Test Main Inverter Board Figure F.21 Main Board LocationTable F.14 LED Functions Table F.15 Feedback Voltage SignalsTable F.17 LED Check in Stick Mode Table F.16 Voltage Checks with 115 VAC Applied to MachineTP14 TP15 TP16 TP19 TP31 CN4/1-2 Short Circuit Ohms CN5/1-2 Figure F.23 Main Board Lower Left TP9 Ground Power MF15 VDS MF12 MF16 VDSV205-T AC/DC Input Filter Board Removal and Replacement Input Filter Board Removal and Replacement RV1 V205-T AC/DC Main Igbt Board Removal and Replacement Main Igbt Board Removal & Replacement CN2 CN1 V205-T AC/DC CONTROL/DISPLAY Board Removal and Replacement CONTROL/DISPLAY Board Removal & Replacement CN7 CN3V205-T AC/DC Output Filter Board Removal and Replacement Removal and Replacement Casefront Mounting Screws Phillips Head Screws CN1 CN2 Output Diodes Removal and Replacement Output Diodes Figure F.35 Output Diode LocationOutput Transistor Removal and Replacement Output Transistor Removal and Replacement Plug CN1 5mm V205-T AC/DC Electrical Diagrams Table of Contents Electrical Diagrams SectionWiring Diagram V205-T AC/DC Standard Diagram SVM Error Reporting Form