Makita 6402 DP4700 English, Additional Safety Rules, Operating Instructions, Specifications

Page 3

ENGLISH

 

Explanation of general view

 

 

 

 

 

 

 

 

9

 

1

Side grip

5

Ring

Switch trigger

2

Tighten

6

High

0

Lock button

3

Chuck key

7

Low

q Reversing switch lever

4

Sleeve

8

Speed control screw

w Reversing switch lever

 

 

 

 

 

 

 

 

SPECIFICATIONS

Model

6402

DP4700

Capacities

 

 

Steel

10 mm

13 mm

Wood

21 mm

36 mm

No load speed (RPM)

0 ± 1,200

0 ± 550

Overall length

264 mm

275 mm

Net weight

1.7 kg

2.0 kg

 

 

 

·Due to the continuing program of research and development, the specifications herein are subject to change without prior notice.

·Note: Specifications may differ from country to country.

Power supply

The machine should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed safety instructions.

These symbols mean:

Read instruction manual.

DOUBLE INSULATION

ADDITIONAL SAFETY RULES

1.Always be sure you have a firm footing. Be sure no one is below when using the machine in high locations.

2.Hold the machine firmly.

3.Keep hands away from rotating parts.

4.When drilling into walls, floors or wherever ``live'' electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE MACHINE! Hold the machine by the insulated grasping surfaces to prevent electric shock if you drill into a ``live'' wire.

5.Do not leave the machine running. Operate the machine only when hand-held.

6.Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing side grip (auxiliary handle) (Fig. 1)

For DP4700 only

Screw the side grip on the machine securely.

Installing or removing drill bit

Important:

Always be sure that the machine is switched off and unplugged before installing or removing the bit.

For machines with standard keyed chuck (Fig. 2) To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise. Be sure to tighten all three chuck holes evenly. To remove the bit, turn the chuck key counterclockwise in just one hole, then loosen the chuck by hand.

After using the chuck key, be sure to return it to the original position.

For machines with keyless chuck (Fig. 3)

Hold the ring and turn the sleeve counterciockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clockwise to tighten the chuck. To remove the bit, hold the ring and turn the sleeve counterclockwise.

Switch action (Fig. 4)

CAUTION:

Before plugging in the machine, always check to see that the switch trigger actuates properly and returns to the ``OFF'' position when released.

To start the machine, simply pull the trigger. Machine speed is increased by increasing pressure on the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the machine from the locked position, pull the trigger fully, then release it. A speed control screw is provided so that maximum machine speed can be limited (variable). Turn the speed control screw clockwise for higher speed, and counterclock- wise for lower speed.

3

Image 3
Contents 10 mm Mm DP4700 Page Operating Instructions Additional Safety RulesSpecifications EnglishDrilling operation MaintenanceGuarantee Reversing switch actionDescriptif Conservez CES Instructions Mode DemploiFrançais Consignes DE Securite SupplementairesInverseur de marche EntretienGarantie Interrupteur FigMontage des Zusatzhandgriffs Abb DeutschZusätzliche Sicherheitsbestimmungen Technische DatenBohren WartungSchalterfunktion Abb Drehrichtungsumschalter Abb für DP4700 u. Abb fürConservate Queste Istruzioni ItalianoRegole Addizionali DI Sicurezza Istruzioni PER LusoInterruttore di inversione di marcia ManutenzioneGaranzia Operazione dellinterruttore FigTechnische Gegevens NederlandsAanvullende Veiligheidsvoorschriften Bewaar Deze Voorschriften BedieningsvoorschriftenBoren OnderhoudWerking van de schakelaar Fig Werking van de omkeerschakelaarInstalación de la empuñadura lateral manija auxiliar Fig Normas DE Seguridad AdicionalesExplicación de los dibujos EspecificacionesOperación de perforación MantenimientoInterruptor de encendido Fig Acción del interruptor inversorRegras DE Segurança Adicionais PortuguêsPrecaução GarantiaInterruptor Fig PerfuraçaÄ oGEM Disse Forskrifter DanskYderligere Sikkerhedsbestemmelser AnvendelseOmlùbsvñlgerbetjening VedligeholdelseGaranti Afbryderkontaktbetjening FigSpara Dessa Anvisningar SvenskaKompletterande SÄKERHETS- Föreskrifter BruksanvisningUnderhåll Omkastning av rotationsriktningenBorrningsdrift TA Vare PÅ Disse Instruksene NorskBruksanvisninger Ekstra SikkerhetsreglerReversering for modell DP4700 og for modell ServiceSäilytä Nämä Ohjeet SuomiLisäturvaohjeita KäyttöohjeetPoraaminen HuoltoTakuu Kytkimen käyttö Kuva∂§§∏¡π∞ ¡Δ∏ƒ∏∏ Page Page Page Page Page Makita Corporation